sailing yacht a layout

• Yachting World
• Digital Edition

43 of the best bluewater sailboat designs of all time

• January 5, 2022

How do you choose the right yacht for you? We highlight the very best bluewater sailboat designs for every type of cruising

Which yacht is the best for bluewater boating? This question generates even more debate among sailors than questions about what’s the coolest yacht , or the best for racing. Whereas racing designs are measured against each other, cruising sailors get very limited opportunities to experience different yachts in real oceangoing conditions, so what is the best bluewater sailboat?

Here, we bring you our top choices from decades of designs and launches. Over the years, the Yachting World team has sailed these boats, tested them or judged them for European Yacht of the Year awards, and we have sifted through the many to curate a selection that we believe should be on your wishlist.

Making the right choice may come down to how you foresee your yacht being used after it has crossed an ocean or completed a passage: will you be living at anchor or cruising along the coast? If so, your guiding requirements will be space, cabin size, ease of launching a tender and anchoring closer to shore, and whether it can comfortably accommodate non-expert-sailor guests.

Article continues below…

The perfect boat: what makes an ideal offshore cruising yacht?

Choosing a boat for offshore cruising is not a decision to be taken lightly. I have researched this topic on…

European Yacht of the Year 2019: Best luxury cruisers

Before the sea trials began, I would have put money on a Hallberg-Rassy or the Wauquiez winning an award. The…

All of these considerations have generated the inexorable rise of the bluewater catamaran – monohulls can’t easily compete on these points. We have a full separate feature on the best bluewater multihulls of all time and here we mostly focus on monohulls. The only exceptions to that rule are two multihulls which made it into our best bluewater sailboats of 2022 list.

As so much of making the right choice is selecting the right boat for the venture in mind, we have separated out our edit into categories: best for comfort; for families; for performance; and for expedition or high latitudes sailing .

Best bluewater sailboats of 2022

The new flagship Allures 51.9, for example, is a no-nonsense adventure cruising design built and finished to a high standard. It retains Allures’ niche of using aluminium hulls with glassfibre decks and superstructures, which, the yard maintains, gives the optimum combination of least maintenance and less weight higher up. Priorities for this design were a full beam aft cabin and a spacious, long cockpit. Both are excellent, with the latter, at 6m long, offering formidable social, sailing and aft deck zones.

It likes some breeze to come to life on the wheel, but I appreciate that it’s designed to take up to five tonnes payload. And I like the ease with which you can change gears using the furling headsails and the positioning of the powerful Andersen winches inboard. The arch is standard and comes with a textile sprayhood or hard bimini.

Below decks you’ll find abundant headroom and natural light, a deep U-shape galley and cavernous stowage. For those who like the layout of the Amel 50 but would prefer aluminium or shoal draught, look no further.

Allures 51.9 price: €766,000

The Ovni 370 is another cunning new aluminum centreboard offering, a true deck saloon cruiser for two. The designers say the biggest challenge was to create a Category A ocean going yacht at this size with a lifting keel, hence the hull had to be very stable.

Enjoyable to helm, it has a practical, deep cockpit behind a large sprayhood, which can link to the bimini on the arch. Many of its most appealing features lie in the bright, light, contemporary, clever, voluminous interior, which has good stowage and tankage allocation. There’s also a practical navstation, a large workroom and a vast separate shower. I particularly like the convertible saloom, which can double as a large secure daybed or pilot berth.

Potentially the least expensive Category A lift keel boat available, the Ovni will get you dreaming of remote places again.

Ovni 370 price: €282,080

There’s no shortage of spirit in the Windelo 50. We gave this a sustainability award after it’s founders spent two years researching environmentally-friendly composite materials, developing an eco-composite of basalt fibre and recycled PET foam so it could build boats that halve the environmental impact of standard glassfibre yachts.

The Windelo 50 is an intriguing package – from the styling, modular interior and novel layout to the solar field on the roof and the standard electric propulsion, it is completely fresh.

Windelo 50 price: €795,000

Best bluewater sailboat of 2022 – Outremer 55

I would argue that this is the most successful new production yacht on the market. Well over 50 have already sold (an equipped model typically costs €1.6m) – and I can understand why. After all, were money no object, I had this design earmarked as the new yacht I would most likely choose for a world trip.

Indeed 55 number one Sanya, was fully equipped for a family’s world cruise, and left during our stay for the Grand Large Odyssey tour. Whereas we sailed Magic Kili, which was tricked up with performance options, including foam-cored deckheads and supports, carbon crossbeam and bulkheads, and synthetic rigging.

At rest, these are enticing space ships. Taking one out to sea is another matter though. These are speed machines with the size, scale and loads to be rightly weary of. Last month Nikki Henderson wrote a feature for us about how to manage a new breed of performance cruising cats just like this and how she coaches new owners. I could not think of wiser money spent for those who do not have ample multihull sailing experience.

Under sail, the most fun was obviously reserved for the reaching leg under asymmetric, where we clocked between 11-16 knots in 15-16 knots wind. But it was the stability and of those sustained low teen speeds which really hit home  – passagemaking where you really cover miles.

Key features include the swing helms, which give you views from outboard, over the coachroof or from a protected position in the cockpit through the coachroof windows, and the vast island in the galley, which is key to an open plan main living area. It helps provide cavernous stowage and acts as the heart of the entertaining space as it would in a modern home. As Danish judge Morten Brandt-Rasmussen comments: “Apart from being the TGV of ocean passages the boat offers the most spacious, open and best integration of the cockpit and salon areas in the market.”

Outremer has done a top job in packing in the creature comforts, stowage space and payload capacity, while keeping it light enough to eat miles. Although a lot to absorb and handle, the 55 offers a formidable blend of speed and luxury cruising.

Outremer 55 price: €1.35m

Best bluewater sailboats for comfort

This is the successor to the legendary Super Maramu, a ketch design that for several decades defined easy downwind handling and fostered a cult following for the French yard. Nearly a decade old, the Amel 55 is the bridge between those world-girdling stalwarts and Amel’s more recent and totally re-imagined sloop designs, the Amel 50 and 60.

The 55 boasts all the serious features Amel aficionados loved and valued: a skeg-hung rudder, solidly built hull, watertight bulkheads, solid guardrails and rampart bulwarks. And, most noticeable, the solid doghouse in which the helmsman sits in perfect shelter at the wheel.

This is a design to live on comfortably for long periods and the list of standard features just goes on and on: passarelle; proper sea berths with lee cloths; electric furling main and genoa; and a multitude of practical items that go right down to a dishwasher and crockery.

There’s no getting around the fact these designs do look rather dated now, and through the development of easier sail handling systems the ketch rig has fallen out of fashion, but the Amel is nothing short of a phenomenon, and if you’ve never even peeked on board one, you really have missed a treat.

Photo: Sander van der Borch

Contest 50CS

A centre cockpit cruiser with true longevity, the Contest 50CS was launched by Conyplex back in 2003 and is still being built by the family-owned Dutch company, now in updated and restyled form.

With a fully balanced rudder, large wheel and modern underwater sections, the Contest 50CS is a surprisingly good performer for a boat that has a dry weight of 17.5 tonnes. Many were fitted with in-mast furling, which clearly curtails that performance, but even without, this boat is set up for a small crew.

Electric winches and mainsheet traveller are all easy to reach from the helm. On our test of the Contest 50CS, we saw for ourselves how two people can gybe downwind under spinnaker without undue drama. Upwind, a 105% genoa is so easy to tack it flatters even the weediest crewmember.

Down below, the finish level of the joinery work is up there among the best and the interior is full of clever touches, again updated and modernised since the early models. Never the cheapest bluewater sailing yacht around, the Contest 50CS has remained in demand as a brokerage buy. She is a reassuringly sure-footed, easily handled, very well built yacht that for all those reasons has stood the test of time.

This is a yacht that would be well capable of helping you extend your cruising grounds, almost without realising it.

Read more about the Contest 50CS and the new Contest 49CS

Photo: Rick Tomlinson

Hallberg-Rassy 48 Mk II

For many, the Swedish Hallberg-Rassy yard makes the quintessential bluewater cruiser for couples. With their distinctive blue cove line, these designs are famous for their seakindly behaviour, solid-as-a-rock build and beautifully finished, traditional interiors.

To some eyes, Hallberg-Rassys aren’t quite cool enough, but it’s been company owner Magnus Rassy’s confidence in the formula and belief in incremental ‘step-by-step’ evolution that has been such an exceptional guarantor of reliable quality, reputation and resale value.

The centre cockpit Hallberg-Rassy 48 epitomises the concept of comfort at sea and, like all the Frers-designed Hallberg-Rassys since the 1990s, is surprisingly fleet upwind as well as steady downwind. The 48 is perfectly able to be handled by a couple (as we found a few years back in the Pacific), and could with no great effort crack out 200-mile days.

The Hallberg-Rassy 48 was launched nearly a decade ago, but the Mk II from 2014 is our pick, updated with a more modern profile, larger windows and hull portlights that flood the saloon and aft cabin with light. With a large chart table, secure linear galley, heaps of stowage and space for bluewater extras such as machinery and gear, this yacht pretty much ticks all the boxes.

Discovery 55

First launched in 2000, the Discovery 55 has stood the test of time. Designed by Ron Holland, it hit a sweet spot in size that appealed to couples and families with world girdling plans.

Elegantly styled and well balanced, the 55 is also a practical design, with a deep and secure cockpit, comfortable seating, a self-tacking jib, dedicated stowage for the liferaft , a decent sugar scoop transom that’s useful for swimming or dinghy access, and very comfortable accommodation below. In short, it is a design that has been well thought out by those who’ve been there, got the bruises, stubbed their toes and vowed to change things in the future if they ever got the chance.

Throughout the accommodation there are plenty of examples of good detailing, from the proliferation of handholds and grabrails, to deep sinks in the galley offering immediate stowage when under way and the stand up/sit down showers. Stowage is good, too, with plenty of sensibly sized lockers in easily accessible positions.

The Discovery 55 has practical ideas and nifty details aplenty. She’s not, and never was, a breakthrough in modern luxury cruising but she is pretty, comfortable to sail and live on, and well mannered.

Photo: Latitudes Picture Library

You can’t get much more Cornish than a Rustler. The hulls of this Stephen Jones design are hand-moulded and fitted out in Falmouth – and few are more ruggedly built than this traditional, up-for-anything offshore cruiser.

She boasts an encapsulated lead keel, eliminating keel bolts and creating a sump for generous fuel and water tankage, while a chunky skeg protects the rudder. She is designed for good directional stability and load carrying ability. These are all features that lend this yacht confidence as it shoulders aside the rough stuff.

Most of those built have had a cutter rig, a flexible arrangement that makes sense for long passages in all sea and weather conditions. Down below, the galley and saloon berths are comfortable and sensible for living in port and at sea, with joinery that Rustler’s builders are rightly proud of.

As modern yachts have got wider, higher and fatter, the Rustler 42 is an exception. This is an exceptionally well-mannered seagoing yacht in the traditional vein, with elegant lines and pleasing overhangs, yet also surprisingly powerful. And although now over 20 years old, timeless looks and qualities mean this design makes her look ever more like a perennial, a modern classic.

The definitive crossover size, the point at which a yacht can be handled by a couple but is just large enough to have a professional skipper and be chartered, sits at around the 60ft mark. At 58ft 8in, the Oyster 575 fitted perfectly into this growing market when launched in 2010. It went on to be one of the most popular models from the yard, and is only now being superseded by the newer Rob Humphreys-designed Oyster 565 (just launched this spring).

Built in various configurations with either a deep keel, shoal draught keel or centreboard with twin rudders, owners could trade off better performance against easy access to shallower coves and anchorages. The deep-bodied hull, also by Rob Humphreys, is known for its easy motion at sea.

Some of the Oyster 575’s best features include its hallmark coachroof windows style and centre cockpit – almost everyone will know at first glance this is an Oyster – and superb interior finish. If she has a flaw, it is arguably the high cockpit, but the flip side is the galley headroom and passageway berth to the large aft stateroom.

This design also has a host of practical features for long-distance cruising, such as high guardrails, dedicated liferaft stowage, a vast lazarette for swallowing sails, tender, fenders etc, and a penthouse engine room.

Privilege Serie 5

A true luxury catamaran which, fully fitted out, will top €1m, this deserves to be seen alongside the likes of the Oyster 575, Gunfleet 58 and Hallberg-Rassy 55. It boasts a large cockpit and living area, and a light and spacious saloon with an emphasis on indoor-outdoor living, masses of refrigeration and a big galley.

Standout features are finish quality and solid build in a yacht designed to take a high payload, a secure walkaround deck and all-round views from the helm station. The new Privilege 510 that will replace this launches in February 2020.

Gunfleet 43

It was with this Tony Castro design that Richard Matthews, founder of Oyster Yachts, launched a brand new rival brand in 2012, the smallest of a range stretching to the flagship Gunfleet 74. The combination of short overhangs and centre cockpit at this size do make the Gunfleet 43 look modern if a little boxy, but time and subsequent design trends have been kind to her lines, and the build quality is excellent. The saloon, galley and aft cabin space is exceptional on a yacht of this size.

Photo: David Harding

Conceived as a belt-and-braces cruiser, the Kraken 50 launched last year. Its unique points lie underwater in the guise of a full skeg-hung rudder and so-called ‘Zero Keel’, an encapsulated long keel with lead ballast.

Kraken Yachts is the brainchild of British businessman and highly experienced cruiser Dick Beaumont, who is adamant that safety should be foremost in cruising yacht design and build. “There is no such thing as ‘one yacht for all purposes’… You cannot have the best of all worlds, whatever the salesman tells you,” he says.

Read our full review of the Kraken 50 .

Wauquiez Centurion 57

Few yachts can claim to be both an exciting Med-style design and a serious and practical northern European offshore cruiser, but the Wauquiez Centurion 57 tries to blend both. She slightly misses if you judge solely by either criterion, but is pretty and practical enough to suit her purpose.

A very pleasant, well-considered yacht, she is impressively built and finished with a warm and comfortable interior. More versatile than radical, she could be used for sailing across the Atlantic in comfort and raced with equal enjoyment at Antigua Sailing Week .

A modern classic if ever there was one. A medium to heavy displacement yacht, stiff and easily capable of standing up to her canvas. Pretty, traditional lines and layout below.

Photo: Voyage of Swell

Well-proven US legacy design dating back to the mid-1960s that once conquered the Transpac Race . Still admired as pretty, with slight spoon bow and overhanging transom.

Capable medium displacement cruiser, ideal size and good accommodation for couples or family cruising, and much less costly than similar luxury brands.

Photo: Peter Szamer

Swedish-built aft cockpit cruiser, smaller than many here, but a well-built and finished, super-durable pocket ocean cruiser.

Tartan 3700

Designed as a performance cruiser there are nimbler alternatives now, but this is still an extremely pretty yacht.

Broker ’ s choice

Discovery 55 Brizo

This yacht has already circumnavigated the globe and is ‘prepared for her next adventure,’ says broker Berthon. Price: £535,000 + VAT

Oyster 575 Ayesha

‘Stunning, and perfectly equipped for bluewater cruising,’ says broker Ancasta International. Price: £845,000 (tax not paid)

Oyster 575 Pearls of Nautilus

Nearly new and with a high spec, this Oyster Brokerage yacht features American white oak joinery and white leather upholstery and has a shoal draught keel. Price: $1.49m

Best bluewater yachts for performance

The Frers-designed Swan 54 may not be the newest hull shape but heralded Swan’s latest generation of displacement bluewater cruisers when launched four years ago. With raked stem, deep V hull form, lower freeboard and slight curve to the topsides she has a more timeless aesthetic than many modern slab-sided high volume yachts, and with that a seakindly motion in waves. If you plan to cover many miles to weather, this is probably the yacht you want to be on.

Photo: Carlo Borlenghi

Besides Swan’s superlative build quality, the 54 brings many true bluewater features, including a dedicated sail locker. There’s also a cockpit locker that functions as a utility cabin, with potential to hold your generator and washing machine, or be a workshop space.

The sloping transom opens out to reveal a 2.5m bathing platform, and although the cabins are not huge there is copious stowage space. Down below the top-notch oak joinery is well thought through with deep fiddles, and there is a substantial nav station. But the Swan 54 wins for handling above all, with well laid-out sail controls that can be easily managed between a couple, while offering real sailing enjoyment to the helmsman.

Photo: Graham Snook

The Performance Cruiser winner at the 2019 European Yacht of the Year awards, the Arcona 435 is all about the sailing experience. She has genuine potential as a cruiser-racer, but her strengths are as an enjoyable cruiser rather than a full-blown liveaboard bluewater boat.

Build quality is excellent, there is the option of a carbon hull and deck, and elegant lines and a plumb bow give the Arcona 435 good looks as well as excellent performance in light airs. Besides slick sail handling systems, there are well thought-out features for cruising, such as ample built-in rope bins and an optional semi-closed stern with stowage and swim platform.

Outremer 51

If you want the space and stability of a cat but still prioritise sailing performance, Outremer has built a reputation on building catamarans with true bluewater characteristics that have cruised the planet for the past 30 years.

Lighter and slimmer-hulled than most cruising cats, the Outremer 51 is all about sailing at faster speeds, more easily. The lower volume hulls and higher bridgedeck make for a better motion in waves, while owners report that being able to maintain a decent pace even under reduced canvas makes for stress-free passages. Deep daggerboards also give good upwind performance.

With bucket seats and tiller steering options, the Outremer 51 rewards sailors who want to spend time steering, while they’re famously well set up for handling with one person on deck. The compromise comes with the interior space – even with a relatively minimalist style, there is less cabin space and stowage volume than on the bulkier cats, but the Outremer 51 still packs in plenty of practical features.

The Xc45 was the first cruising yacht X-Yachts ever built, and designed to give the same X-Yachts sailing experience for sailors who’d spent years racing 30/40-footer X- and IMX designs, but in a cruising package.

Launched over 10 years ago, the Xc45 has been revisited a few times to increase the stowage and modernise some of the styling, but the key features remain the same, including substantial tanks set low for a low centre of gravity, and X-Yachts’ trademark steel keel grid structure. She has fairly traditional styling and layout, matched with solid build quality.

A soft bilge and V-shaped hull gives a kindly motion in waves, and the cockpit is secure, if narrow by modern standards.

A three or four cabin catamaran that’s fleet of foot with high bridgedeck clearance for comfortable motion at sea. With tall daggerboards and carbon construction in some high load areas, Catana cats are light and quick to accelerate.

Sweden Yachts 45

An established bluewater design that also features in plenty of offshore races. Some examples are specced with carbon rig and retractable bowsprits. All have a self-tacking jib for ease. Expect sweeping areas of teak above decks and a traditionally wooded interior with hanging wet locker.

A vintage performer, first launched in 1981, the 51 was the first Frers-designed Swan and marked a new era of iconic cruiser-racers. Some 36 of the Swan 51 were built, many still actively racing and cruising nearly 40 years on. Classic lines and a split cockpit make this a boat for helming, not sunbathing.

Photo: Julien Girardot / EYOTY

The JPK 45 comes from a French racing stable, combining race-winning design heritage with cruising amenities. What you see is what you get – there are no superfluous headliners or floorboards, but there are plenty of ocean sailing details, like inboard winches for safe trimming. The JPK 45 also has a brilliantly designed cockpit with an optional doghouse creating all-weather shelter, twin wheels and superb clutch and rope bin arrangement.

Photo: Andreas Lindlahr

For sailors who don’t mind exchanging a few creature comforts for downwind planing performance, the Pogo 50 offers double-digit surfing speeds for exhilarating tradewind sailing. There’s an open transom, tiller steering and no backstay or runners. The Pogo 50 also has a swing keel, to nose into shallow anchorages.

Seawind 1600

Seawinds are relatively unknown in Europe, but these bluewater cats are very popular in Australia. As would be expected from a Reichel-Pugh design, this 52-footer combines striking good looks and high performance, with fine entry bows and comparatively low freeboard. Rudders are foam cored lifting designs in cassettes, which offer straightforward access in case of repairs, while daggerboards are housed under the deck.

Best bluewater sailboats for families

It’s unsurprising that, for many families, it’s a catamaran that meets their requirements best of increased space – both living space and separate cabins for privacy-seeking teenagers, additional crew or visiting family – as well as stable and predictable handling.

Photo: Nicholas Claris

Undoubtedly one of the biggest success stories has been the Lagoon 450, which, together with boats like the Fountaine Pajot 44, helped drive up the popularity of catamaran cruising by making it affordable and accessible. They have sold in huge numbers – over 1,000 Lagoon 450s have been built since its launch in 2010.

The VPLP-designed 450 was originally launched with a flybridge with a near central helming position and upper level lounging areas (450F). The later ‘sport top’ option (450S) offered a starboard helm station and lower boom (and hence lower centre of gravity for reduced pitching). The 450S also gained a hull chine to create additional volume above the waterline. The Lagoon features forward lounging and aft cockpit areas for additional outdoor living space.

Besides being a big hit among charter operators, Lagoons have proven themselves over thousands of bluewater miles – there were seven Lagoon 450s in last year’s ARC alone. In what remains a competitive sector of the market, Lagoon has recently launched a new 46, with a larger self-tacking jib and mast moved aft, and more lounging areas.

Photo: Gilles Martin-Raget

Fountaine Pajot Helia 44

The FP Helia 44 is lighter, lower volume, and has a lower freeboard than the Lagoon, weighing in at 10.8 tonnes unloaded (compared to 15 for the 450). The helm station is on a mezzanine level two steps up from the bridgedeck, with a bench seat behind. A later ‘Evolution’ version was designed for liveaboard cruisers, featuring beefed up dinghy davits and an improved saloon space.

Available in three or four cabin layouts, the Helia 44 was also popular with charter owners as well as families. The new 45 promises additional volume, and an optional hydraulically lowered ‘beach club’ swim platform.

Photo: Arnaud De Buyzer / graphikup.com

The French RM 1370 might be less well known than the big brand names, but offers something a little bit different for anyone who wants a relatively voluminous cruising yacht. Designed by Marc Lombard, and beautifully built from plywood/epoxy, the RM is stiff and responsive, and sails superbly.

The RM yachts have a more individual look – in part down to the painted finish, which encourages many owners to personalise their yachts, but also thanks to their distinctive lines with reverse sheer and dreadnought bow. The cockpit is well laid out with the primary winches inboard for a secure trimming position. The interior is light, airy and modern, although the open transom won’t appeal to everyone.

For those wanting a monohull, the Hanse 575 hits a similar sweet spot to the popular multis, maximising accommodation for a realistic price, yet with responsive performance.

The Hanse offers a vast amount of living space thanks to the ‘loft design’ concept of having all the living areas on a single level, which gives a real feeling of spaciousness with no raised saloon or steps to accommodation. The trade-off for such lofty head height is a substantial freeboard – it towers above the pontoon, while, below, a stepladder is provided to reach some hatches.

Galley options include drawer fridge-freezers, microwave and coffee machine, and the full size nav station can double up as an office or study space.

But while the Hanse 575 is a seriously large boat, its popularity is also down to the fact that it is genuinely able to be handled by a couple. It was innovative in its deck layout: with a self-tacking jib and mainsheet winches immediately to hand next to the helm, one person could both steer and trim.

Direct steering gives a feeling of control and some tangible sailing fun, while the waterline length makes for rapid passage times. In 2016 the German yard launched the newer Hanse 588 model, having already sold 175 of the 575s in just four years.

Photo: Bertel Kolthof

Jeanneau 54

Jeanneau leads the way among production builders for versatile all-rounder yachts that balance sail performance and handling, ergonomics, liveaboard functionality and good looks. The Jeanneau 54 , part of the range designed by Philippe Briand with interior by Andrew Winch, melds the best of the larger and smaller models and is available in a vast array of layout options from two cabins/two heads right up to five cabins and three heads.

We’ve tested the Jeanneau 54 in a gale and very light winds, and it acquitted itself handsomely in both extremes. The primary and mainsheet winches are to hand next to the wheel, and the cockpit is spacious, protected and child-friendly. An electric folding swim and sun deck makes for quick fun in the water.

Nautitech Open 46

This was the first Nautitech catamaran to be built under the ownership of Bavaria, designed with an open-plan bridgedeck and cockpit for free-flowing living space. But with good pace for eating up bluewater miles, and aft twin helms rather than a flybridge, the Nautitech Open 46 also appeals to monohull sailors who prefer a more direct sailing experience.

Made by Robertson and Caine, who produce catamarans under a dual identity as both Leopard and the Sunsail/Moorings charter cats, the Leopard 45 is set to be another big seller. Reflecting its charter DNA, the Leopard 45 is voluminous, with stepped hulls for reduced waterline, and a separate forward cockpit.

Built in South Africa, they are robustly tested off the Cape and constructed ruggedly enough to handle heavy weather sailing as well as the demands of chartering.

Photo: Olivier Blanchet

If space is king then three hulls might be even better than two. The Neel 51 is rare as a cruising trimaran with enough space for proper liveaboard sailing. The galley and saloon are in the large central hull, together with an owner’s cabin on one level for a unique sensation of living above the water. Guest or family cabins lie in the outer hulls for privacy and there is a cavernous full height engine room under the cabin sole.

Performance is notably higher than an equivalent cruising cat, particularly in light winds, with a single rudder giving a truly direct feel in the helm, although manoeuvring a 50ft trimaran may daunt many sailors.

Beneteau Oceanis 46.1

A brilliant new model from Beneteau, this Finot Conq design has a modern stepped hull, which offers exhilarating and confidence-inspiring handling in big breezes, and slippery performance in lighter winds.

The Beneteau Oceanis 46.1 was the standout performer at this year’s European Yacht of the Year awards, and, in replacing the popular Oceanis 45, looks set to be another bestseller. Interior space is well used with a double island berth in the forepeak. An additional inboard unit creates a secure galley area, but tank capacity is moderate for long periods aboard.

Beneteau Oceanis 473

A popular model that offers beam and height in a functional layout, although, as with many boats of this age (she was launched in 2002), the mainsheet is not within reach of the helmsman.

Jeanneau Sun Odyssey 49

The Philippe Briand-designed Sun Odyssey range has a solid reputation as family production cruisers. Like the 473, the Sun Odyssey 49 was popular for charter so there are plenty of four-cabin models on the market.

Nautitech 441

The hull design dates back to 1995, but was relaunched in 2012. Though the saloon interior has dated, the 441 has solid practical features, such as a rainwater run-off collection gutter around the coachroof.

Atlantic 42

Chris White-designed cats feature a pilothouse and forward waist-high working cockpit with helm position, as well as an inside wheel at the nav station. The Atlantic 42 offers limited accommodation by modern cat standards but a very different sailing experience.

Best bluewater sailing yachts for expeditions

Bestevaer 56.

All of the yachts in our ‘expedition’ category are aluminium-hulled designs suitable for high latitude sailing, and all are exceptional yachts. But the Bestevaer 56 is a spectacular amount of boat to take on a true adventure. Each Bestevaer is a near-custom build with plenty of bespoke options for owners to customise the layout and where they fall on the scale of rugged off-grid adventurer to 4×4-style luxury fit out.

The Bestevaer range began when renowned naval architect Gerard Dijkstra chose to design his own personal yacht for liveaboard adventure cruising, a 53-footer. The concept drew plenty of interest from bluewater sailors wanting to make longer expeditions and Bestevaers are now available in a range of sizes, with the 56-footer proving a popular mid-range length.

The well-known Bestevaer 56 Tranquilo  (pictured above) has a deep, secure cockpit, voluminous tanks (700lt water and over 1,100lt fuel) and a lifting keel plus water ballast, with classically styled teak clad decks and pilot house. Other owners have opted for functional bare aluminium hull and deck, some choose a doghouse and others a pilothouse.

Photo: Jean-Marie Liot

The Boreal 52 also offers Land Rover-esque practicality, with utilitarian bare aluminium hulls and a distinctive double-level doghouse/coachroof arrangement for added protection in all weathers. The cockpit is clean and uncluttered, thanks to the mainsheet position on top of the doghouse, although for visibility in close manoeuvring the helmsman will want to step up onto the aft deck.

Twin daggerboards, a lifting centreboard and long skeg on which she can settle make this a true go-anywhere expedition yacht. The metres of chain required for adventurous anchoring is stowed in a special locker by the mast to keep the weight central. Down below has been thought through with equally practical touches, including plenty of bracing points and lighting that switches on to red light first to protect your night vision.

Photo: Morris Adant / Garcia Yachts

Garcia Exploration 45

The Garcia Exploration 45 comes with real experience behind her – she was created in association with Jimmy Cornell, based on his many hundreds of thousands of miles of bluewater cruising, to go anywhere from high latitudes to the tropics.

Arguably less of a looker than the Bestevaer, the Garcia Exploration 45 features a rounded aluminium hull, centreboard with deep skeg and twin daggerboards. The considerable anchor chain weight has again been brought aft, this time via a special conduit to a watertight locker in front of the centreboard.

This is a yacht designed to be lived on for extended periods with ample storage, and panoramic portlights to give a near 360° view of whichever extraordinary landscape you are exploring. Safety features include a watertight companionway door to keep extreme weather out and through-hull fittings placed above the waterline. When former Vendée Globe skipper Pete Goss went cruising , this was the boat he chose to do it in.

Photo: svnaima.com

A truly well-proven expedition design, some 1,500 Ovnis have been built and many sailed to some of the most far-flung corners of the world. (Jimmy Cornell sailed his Aventura some 30,000 miles, including two Drake Passage crossings, one in 50 knots of wind).

Futuna Exploration 54

Another aluminium design with a swinging centreboard and a solid enclosed pilothouse with protected cockpit area. There’s a chunky bowsprit and substantial transom arch to house all manner of electronics and power generation.

Previous boats have been spec’d for North West Passage crossings with additional heating and engine power, although there’s a carbon rig option for those that want a touch of the black stuff. The tanks are capacious, with 1,000lt capability for both fresh water and fuel.

If you enjoyed this….

Yachting World is the world’s leading magazine for bluewater cruisers and offshore sailors. Every month we have inspirational adventures and practical features to help you realise your sailing dreams. Build your knowledge with a subscription delivered to your door. See our latest offers and save at least 30% off the cover price.

Yachting Monthly

• Digital edition

25 of the best small sailing boat designs

• Nic Compton
• August 10, 2022

Nic Compton looks at the 25 yachts under 40ft which have had the biggest impact on UK sailing

There’s nothing like a list of best small sailing boat designs to get the blood pumping.

Everyone has their favourites, and everyone has their pet hates.

This is my list of the 25 best small sailing boat designs, honed down from the list of 55 yachts I started with.

I’ve tried to be objective and have included several boats I don’t particularly like but which have undeniably had an impact on sailing in the UK – and yes, it would be quite a different list if I was writing about another country.

If your favourite isn’t on the best small sailing boat designs list, then send an email to [email protected] to argue the case for your best-loved boat.

Ready? Take a deep breath…

Credit: Bob Aylott

Laurent Giles is best known for designing wholesome wooden cruising boats such as the Vertue and Wanderer III , yet his most successful design was the 26ft Centaur he designed for Westerly, of which a remarkable 2,444 were built between 1969 and 1980.

It might not be the prettiest boat on the water, but it sure packs a lot of accommodation.

The Westerly Centaur was one of the first production boats to be tank tested, so it sails surprisingly well too. Jack L Giles knew what he was doing.

Colin Archer

Credit: Nic Compton

Only 32 Colin Archer lifeboats were built during their designer’s lifetime, starting with Colin Archer in 1893 and finishing with Johan Bruusgaard in 1924.

Yet their reputation for safety spawned hundreds of copycat designs, the most famous of which was Sir Robin Knox-Johnston ’s Suhaili , which he sailed around the world singlehanded in 1968-9.

The term Colin Archer has become so generic it is often used to describe any double-ender – so beware!

Contessa 32

Assent ‘s performance in the 1979 Fastnet Race makes the Contessa 32 a worth entry in the 25 best small sailing boat designs list. Credit: Nic Compton

Designed by David Sadler as a bigger alternative to the popular Contessa 26, the Contessa 32 was built by Jeremy Rogers in Lymington from 1970.

The yacht’s credentials were established when Assent , the Contessa 32 owned by Willy Kerr and skippered by his son Alan, became the only yacht in her class to complete the deadly 1979 Fastnet Race .

When UK production ceased in 1983, more than 700 had been built, and another 20 have been built since 1996.

Cornish Crabber 24

It seemed a daft idea to build a gaff-rigged boat in 1974, just when everyone else had embraced the ‘modern’ Bermudan rig.

Yet the first Cornish Crabber 24, designed by Roger Dongray, tapped into a feeling that would grow and grow and eventually become a movement.

The 24 was followed in 1979 by the even more successful Shrimper 19 – now ubiquitous in almost every harbour in England – and the rest is history.

Drascombe Lugger

Credit: David Harding

There are faster, lighter and more comfortable boats than a Drascombe Lugger.

And yet, 57 years after John Watkinson designed the first ‘lugger’ (soon changed to gunter rig), more than 2,000 have been built and the design is still going strong.

More than any other boat, the Drascombe Lugger opened up dinghy cruising, exemplified by Ken Duxbury’s Greek voyages in the 1970s and Webb Chiles’s near-circumnavigation on Chidiock Tichbourne I and II .

The 26ft Eventide. Credit: David Harding

It’s been described as the Morris Minor of the boating world – except that the majority of the 1,000 Eventides built were lovingly assembled by their owners, not on a production line.

After you’d tested your skills building the Mirror dinghy, you could progress to building a yacht.

And at 24ft long, the Eventide packed a surprising amount of living space.

It was Maurice Griffiths’ most successful design and helped bring yachting to a wider audience.

You either love ’em or you hate ’em – motorsailers, that is.

The Fisher 30 was brought into production in 1971 and was one of the first out-and-out motorsailers.

With its long keel , heavy displacement and high bulwarks, it was intended to evoke the spirit of North Sea fishing boats.

It might not sail brilliantly but it provided an exceptional level of comfort for its size and it would look after you when things turned nasty.

Significantly, it was also fitted with a large engine.

Credit: Rupert Holmes

It should have been a disaster.

In 1941, when the Scandinavian Sailing Federation couldn’t choose a winner for their competition to design an affordable sailing boat, they gave six designs to naval architect Tord Sundén and asked him to combine the best features from each.

The result was a sweet-lined 25ft sloop which was very seaworthy and fast.

The design has been built in GRP since the 1970s and now numbers more than 4,000, with fleets all over the world.

Credit: Kevin Barber

There’s something disconcerting about a boat with two unstayed masts and no foresails, and certainly the Freedom range has its detractors.

Yet as Garry Hoyt proved, first with the Freedom 40, designed in collaboration with Halsey Herreshoff, and then the Freedom 33 , designed with Jay Paris, the boats are simple to sail (none of those clattering jib sheets every time you tack) and surprisingly fast – at least off the wind .

Other ‘cat ketch’ designs followed but the Freedoms developed their own cult following.

Hillyard 12-tonner

The old joke about Hillyards is that you won’t drown on one but you might starve to death getting there.

And yet this religious boatbuilder from Littlehampton built up to 800 yachts which travelled around the world – you can find them cruising far-flung destinations.

Sizes ranged from 2.5 to 20 tons, though the 9- and 12-ton are best for long cruises.

The innovations on Jester means she is one of the best small sailing boat designs in the last 100 years. Credit: Ewen Southby-Tailyour

Blondie Hasler was one of the great sailing innovators and Jester was his testing ground.

She was enclosed, carvel planked and had an unstayed junk rig.

Steering was via a windvane system Hasler created.

Hasler came second in the first OSTAR , proving small boats can achieve great things.

Moody kicked off the era of comfort-oriented boats with its very first design.

The Moody 33, designed by Angus Primrose, had a wide beam and high topside to produce a voluminous hull .

The centre cockpit allowed for an aft cabin, resulting in a 33-footer with two sleeping cabins – an almost unheard of concept in 1973 –full-beam heads and spacious galley.

What’s more, her performance under sail was more than adequate for cruising.

Finally, here was a yacht that all the family could enjoy.

Continues below…

What makes a boat seaworthy?

What characteristics make a yacht fit for purpose? Duncan Kent explores the meaning of 'seaworthy' and how hull design and…

How boat design is evolving

Will Bruton looks at the latest trends and innovations shaping the boats we sail

How keel type affects performance

James Jermain looks at the main keel types, their typical performance and the pros and cons of each

Boat handling: How to use your yacht’s hull shape to your advantage

Whether you have a long keel or twin keel rudders, there will be pros and cons when it comes to…

Nicholson 32

Credit: Genevieve Leaper

Charles Nicholson was a giant of the wooden boat era but one of his last designs – created with his son Peter – was a pioneering fibreglass boat that would become an enduring classic.

With its long keel and heavy displacement, the Nicholson 32 is in many ways a wooden boat built in fibreglass – and indeed the design was based on Nicholson’s South Coast One Design.

From 1966 to 1977, the ‘Nic 32’ went through 11 variations.

Credit: Hallberg-Rassy

In the beginning there was… the Rasmus 35. This was the first yacht built by the company that would become Hallberg-Rassy and which would eventually build more than 9,000 boats.

The Rasmus 35, designed by Olle Enderlein, was a conservative design, featuring a centre cockpit, long keel and well-appointed accommodation.

Some 760 boats were built between 1967 and 1978.

Credit: Larry & Lin Pardey

Lyle Hess was ahead of his time when he designed Renegade in 1949.

Despite winning the Newport to Ensenada race, the 25ft wooden cutter went largely unnoticed.

Hess had to build bridges for 15 years before Larry Pardey asked him to design the 24ft Seraffyn , closely based on Renegade ’s lines but with a Bermudan rig.

Pardey’s subsequent voyages around the world cemented Hess’s reputation and success of the Renegade design.

Would the Rustler 36 make it on your best small sailing boat list? Credit: Rustler Yachts

Six out of 18 entries for the 2018 Golden Globe Race (GGR) were Rustler 36s, with the top three places all going to Rustler 36 skippers.

It was a fantastic endorsement for a long-keel yacht designed by Holman & Pye 40 years before.

Expect to see more Rustler 36s in the 2022 edition of the GGR!

It was Ted Heath who first brought the S&S 34 to prominence with his boat Morning Cloud .

In 1969 the yacht won the Sydney to Hobart Race, despite being one of the smallest boats in the race.

Other epic S&S 34 voyages include the first ever single-handed double circumnavigation by Jon Sanders in 1981

Credit: Colin Work

The Contessa 32 might seem an impossible boat to improve upon, but that’s what her designer David Sadler attempted to do in 1979 with the launch of the Sadler 32 .

That was followed two years later by the Sadler 29 , a tidy little boat that managed to pack in six berths in a comfortable open-plan interior.

The boat was billed as ‘unsinkable’, with a double-skinned hull separated by closed cell foam buoyancy.

What’s more, it was fast, notching up to 12 knots.

Credit: Dick Durham/Yachting Monthly

Another modern take on the Contessa theme was the Sigma 33, designed by David Thomas in 1979.

A modern underwater body combined with greater beam and higher freeboard produced a faster boat with greater accommodation.

And, like the Contessa, the Sigma 33 earned its stripes at the 1979 Fastnet, when two of the boats survived to tell the tale.

A lively one-design fleet soon developed on the Solent which is still active to this day.

A replica of Joshua Slocum’s Spray . Credit: Alamy Stock Photo

The boat Joshua Slocum used for his first singlehanded circumnavigation of the world wasn’t intended to sail much further than the Chesapeake Bay.

The 37ft Spray was a rotten old oyster sloop which a friend gave him and which he had to spend 13 months fixing up.

Yet this boxy little tub, with its over-optimistic clipper bow, not only took Slocum safely around the world but has spawned dozens of modern copies that have undertaken long ocean passages.

Credit: James Wharram Designs

What are boats for if not for dreaming? And James Wharram had big dreams.

First he sailed across the Atlantic on the 23ft 6in catamaran Tangaroa .

He then built the 40ft Rongo on the beach in Trinidad (with a little help from French legend Bernard Moitessier) and sailed back to the UK.

Then he drew the 34ft Tangaroa (based on Rongo ) for others to follow in his wake and sold 500 plans in 10 years.

Credit: Graham Snook/Yachting Monthly

The Twister was designed in a hurry.

Kim Holman wanted a boat at short notice for the 1963 season and, having had some success with his Stella design (based on the Folkboat), he rushed out a ‘knockabout cruising boat for the summer with some racing for fun’.

The result was a Bermudan sloop that proved nigh on unbeatable on the East Anglian circuit.

It proved to be Holman’s most popular design with more than 200 built.

Credit: Alamy Stock Photo

Laurent Giles’s design No15 was drawn in 1935 for a Guernsey solicitor who wanted ‘a boat that would spin on a sixpence and I could sail single-handed ’.

What the young Jack Giles gave him was a pretty transom-sterned cutter, with a nicely raked stem.

Despite being moderate in every way, the boat proved extremely able and was soon racking up long distances, including Humphrey Barton’s famous transatlantic crossing on Vertue XXXV in 1950.

Wanderer II and III

Credit: Thies Matzen

Eric and Susan Hiscock couldn’t afford a Vertue, so Laurent Giles designed a smaller, 21ft version for them which they named Wanderer II .

They were back a few years later, this time wanting a bigger version: the 30ft Wanderer III .

It was this boat they sailed around the world between 1952-55, writing articles and sailing books along the way.

In doing so, they introduced a whole generation of amateur sailors to the possibilities of long-distance cruising.

Westerly 22

The origins of Westerly Marine were incredibly modest.

Commander Denys Rayner started building plywood dinghies in the 1950s which morphed into a 22ft pocket cruiser called the Westcoaster.

Realising the potential of fibreglass, in 1963 he adapted the design to create the Westerly 22, an affordable cruising boat with bilge keels and a reverse sheer coachroof.

Some 332 boats were built to the design before it was relaunched as the Nomad (267 built).

Enjoyed reading 25 of the best small sailing boat designs?

A subscription to Yachting Monthly magazine costs around 40% less than the cover price .

Print and digital editions are available through Magazines Direct – where you can also find the latest deals .

YM is packed with information to help you get the most from your time on the water.

• Take your seamanship to the next level with tips, advice and skills from our experts
• Impartial in-depth reviews of the latest yachts and equipment
• Cruising guides to help you reach those dream destinations

Follow us on Facebook , Twitter and Instagram.

Bayesian Yacht: A Masterpiece of Luxury and Engineering

The Bayesian yacht, a symbol of nautical elegance and engineering brilliance, has long been celebrated in the world of superyachts. Built by the renowned Italian shipbuilder Perini Navi, this 56-meter vessel was first launched in …

Written by: Kevin Lee

Published on: August 20, 2024

The Bayesian yacht, a symbol of nautical elegance and engineering brilliance, has long been celebrated in the world of superyachts. Built by the renowned Italian shipbuilder Perini Navi, this 56-meter vessel was first launched in 2008 under the name Salute. The name itself, translating to “health” in Italian, seemed to promise a voyage of luxury and well-being. However, what truly set this yacht apart was not just its name, but its sheer opulence, advanced design, and the remarkable story it carried.

The Birth of Bayesian: An Engineering Marvel

Originally costing an estimated £14 million, the Bayesian yacht was a testament to the pinnacle of yacht design and craftsmanship. Perini Navi, one of the world’s leading yacht makers, crafted this vessel with a focus on both performance and luxury. Under the expert design of yacht architect Ron Holland, the Bayesian boasted the world’s tallest aluminum mast, standing over 72 meters above the deck. This engineering feat allowed the yacht to carry nearly 3,000 square meters of sail, making it a sight to behold on the open seas.

The yacht’s towering mast was not just for show; it was a technical challenge that required innovative solutions to ensure stability and safety. A former captain of the Bayesian highlighted the achievement of taming this massive structure, ensuring that it behaved dynamically during both sailing and motoring. This balance between design and function made the Bayesian a unique vessel in the world of superyachts.

A Floating Palace: The Luxurious Interiors

The interiors of the Bayesian yacht were designed by the acclaimed Rémi Tessier, a name synonymous with luxury and sophistication. Tessier, who has also designed suites for Claridge’s hotel in London and yachts for Swiss billionaire Ernesto Bertarelli, infused the Bayesian with a sense of pure and natural elegance. Drawing inspiration from Japanese design principles, Tessier utilized whitened sycamore and teak surfaces in the communal areas, creating a serene and calming environment for guests.

In the private cabins, materials such as stainless steel, ebony, and leather were carefully chosen to create a luxurious yet familiar atmosphere. The yacht could comfortably accommodate up to twelve guests in six beautifully appointed cabins, each attended by a staff of ten, dedicated to catering to every whim of the guests. The design emphasized outdoor living, with ample spaces for al fresco entertaining and relaxing on deck.

The Ultimate Playground: Onboard Amenities and Water Toys

For those fortunate enough to embark on a journey aboard the Bayesian, the yacht offered a plethora of amenities designed for both relaxation and adventure. The lower deck was divided into three distinct sections: crew accommodation towards the bow, guest staterooms in the middle, and the owner’s cabin at the aft. This layout ensured that guests enjoyed privacy and comfort throughout their stay.

The real fun, however, was found at the aft of the yacht, where a garage housed a collection of water toys and crafts. From jet skis and wakeboards to sea kayaks and banana boats, the Bayesian was equipped to offer endless entertainment on the water. A tender was also available to transport guests to secluded bays and ports, allowing them to explore the surrounding areas in style.

A Tragic End: The Sinking of the Bayesian

Despite its luxurious beginnings, the story of the Bayesian yacht took a tragic turn. In 2020, the yacht was refitted and no longer listed for private hire. By this time, it had been renamed Bayesian, a name that would become synonymous with one of the most harrowing maritime incidents in recent history.

In August 2024, during a celebratory voyage off the coast of Sicily, the Bayesian was caught in a sudden and severe storm. High winds, reportedly reaching up to 200km/h, battered the yacht, causing the massive aluminum mast to topple over the side. The force of the wind and the weight of the mast pushed the yacht beyond its down-flooding angle, causing seawater to flood the deck. Within minutes, the Bayesian capsized and sank.

A nearby vessel, the Sir Robert BP, witnessed the tragedy unfold. The crew of the Sir Robert BP reported seeing the Bayesian go flat on the water before disappearing beneath the waves. Despite their efforts to help, only 15 people were rescued from the sinking yacht, including a one-year-old baby who was heroically saved by her mother, Charlotte Golunski.

The Aftermath: A Somber Legacy

The sinking of the Bayesian yacht left a profound impact on the yachting community and beyond. Among those feared dead were tech tycoon Mike Lynch and his daughter Hannah, who were aboard the yacht celebrating Lynch’s recent legal victory in the United States. The tragedy underscored the unpredictable and often dangerous nature of the sea, even for vessels as advanced and well-crafted as the Bayesian.

The wreckage of the Bayesian was eventually discovered by divers, but the loss of life and the yacht itself marked a somber end to what was once a symbol of luxury and achievement. The images of the yacht, once proudly displayed in the homes of its owner, now serve as a poignant reminder of the fragility of life and the unpredictability of nature.

Conclusion: The Enduring Legacy of the Bayesian Yacht

The Bayesian yacht, with its towering mast and luxurious interiors, will always be remembered as a masterpiece of nautical engineering and design. It stood as a symbol of opulence, craftsmanship, and the heights that human ingenuity can reach. Yet, its tragic end also serves as a reminder of the forces of nature and the risks inherent in venturing into the open sea.

For those who had the privilege of experiencing the Bayesian, it was more than just a yacht; it was a floating palace, a testament to the art of yacht-making, and a vessel that carried with it the dreams and aspirations of its owners and guests. Though the Bayesian now rests at the bottom of the Mediterranean, its legacy will continue to inspire and remind us of the delicate balance between luxury and nature.

Frequently Asked Questions (FAQs)

1. What was the original name of the Bayesian yacht? The Bayesian yacht was originally named Salute when it was launched in 2008 by Perini Navi. The name was later changed to Bayesian.

2. Who designed the Bayesian yacht? The design of the Bayesian yacht was a collaboration between Ron Holland, who designed the yacht’s structure, and Rémi Tessier, who created its luxurious interiors.

3. What made the Bayesian yacht unique? The Bayesian yacht was unique for its 72-meter aluminum mast, the tallest in the world, and its luxurious interiors inspired by Japanese design. It was a perfect blend of engineering excellence and opulent living.

4. What led to the sinking of the Bayesian yacht? The Bayesian yacht sank after being caught in a severe storm off the coast of Sicily. High winds caused the mast to topple, which led to the yacht taking on water, capsizing, and sinking quickly.

5. How many people were rescued from the sinking Bayesian yacht? Fifteen people were rescued from the sinking Bayesian yacht, including a one-year-old baby. However, several others, including the yacht’s owner, Mike Lynch, are feared dead.

Leave a Comment Cancel reply

Save my name, email, and website in this browser for the next time I comment.

About Kevin Lee

Oyster 565 Sailing Yacht Design and Layout

The latest yacht in our G6 fleet, the sailing yacht design of the Oyster 565 is configurable to her owner’s needs and preferences. She has been designed for shorthanded family and couples sailing with safety and comfort in mind and is the perfect size to sail comfortably without professional crew.

This Oyster 565 is borne from 43 years of experience building over 120 Oyster 56 and Oyster 575 blue water sailing yachts. From long-distance liveaboard sailing to coastal family cruising, the Oyster 565 makes it all possible. What’s more, with contemporary interiors that can be modified to suit you, you’ll have your pick of joinery, leathers and fabrics to become your on-the-water home. Discover her possible configurations below.

OYSTER 565 EXTERIOR

We understand our owners’ visions to create to perfect yacht. That’s why the Oyster 565 can be built with a variety of different rig configurations and two possible deck plans.

A standard Oyster 565 sail plan for short-handed sailing includes in-mast furling and 105% blade headsail, allowing for easy manoeuvring and sail-handling wherever you are in the world, from relaxed cruising to a global circumnavigation, such as in the  Oyster World Rally .

There is also the option to configure the yacht with a ‘sports pack’ for performance cruising, optimising your Oyster 565 for fast long-distance cruising or sailing events such as the Oyster Regatta.

Keel Options

The Oyster 565’s twin rudder hull form can be combined with a supershoal centreboard for safe shallow-water sailing.

There is an also option for an extended transom which provides large and open aft-deck space for entertaining. This also creates greater storage space ideal for long-distance blue water sailing.

The sailing yacht design of the Oyster 565 can also be customised with a large hydraulic bathing platform, providing quick and easy access to the water when the yacht is at anchor.

OYSTER 565 INTERIOR

The Oyster 565 is available with two personalized layouts designed to suit your preferences tailored to your needs. Browse our typical sailing yacht design layouts below.

Layout 1 - Master Cabin Aft

Our traditional layout positions the master cabin aft, with the two guest cabins forward and a utility cabin which can be lengthened to include an additional berth.

In addition to the midship Seascape windows, which come as standard on all of our G6 range, you can choose to add Seascape windows into the master cabin.

Layout 2 - Master Cabin Forward

The Oyster 565 can be configured with the master cabin forward - a first in Oyster’s yacht design history. This format means the aft section can either stay as one large cabin or be adapted into two double cabins, depending on the number of guests you envisage to have on board with you.

TAKE THE NEXT STEP

Explore the Oyster 565 in more detail on the  Oyster 565 model page . Download the brochure, or contact our expert new-build team to learn how she could be the perfect fit for your family.

Sign up to our newsletter

Be the first to hear about new launches, exclusive events and all things Oyster

© 2024 OYSTER YACHTS

OYSTER WORLD RALLY

Entries for the Oyster World Rally 2028-29 are now open. Embark on the sailing adventure of a lifetime

The new 565 Series II

The pursuit of perfection continues

Oyster Charter

Experience exhilarating sailing, luxury and style on an Oyster charter

New 565 Series II

LUXURY CHARTER

Experience exhilarating sailing, luxury and style on an oyster charter. personal, exclusive and uniquely oyster.

Oyster 825 iSNL

Discover this exceptional late model 825 with a unbeatable spec and a bespoke layout.

oyster ownership

Personalised care, unforgettable experiences and lifelong yacht support, oyster world rally.

ENTRIES OPEN

Embark on the sailing adventure of a lifetime. entries are now open for the oyster world rally 2028-29.

Follow the Oyster World Rally 2024-25 fleet live

Winner of European Yacht of the Year 2023. She is a new breed of luxury 50 foot yacht, offering effortless shorthanded sailing capability.

A magnificent, award-winning sub 60 foot sailing yacht, offering luxurious living space and outstanding shorthanded sailing capability.

A beautifully proportioned 60 foot, luxury liveaboard bluewater cruiser, offering effortless shorthanded sailing capability.

A superb sub 70 foot ocean sailboat offering versatile luxury living space and impeccable sailing performance.

An inspired 75 foot yacht, offering infinite configuration options, generous luxury living space and flexible crew quarters.

Oyster 885SII

The remarkable, iconic 90 foot sailboat, perfect for relaxed luxury voyages of discovery.

First name *

Last name *

Phone number *

Country/Region *

Attach CV *

Attach covering letter

Current occupation

LinkedIn profile

Messing about in boats since 1975.  Online Since 1997.

Home   |  Intro   |  Our Design Process   |  Stock Design Info   |  Motor Yacht Designs   |  Sailing Yacht Designs   |  Prototype Designs Plans List   |  Articles   |  Our CAD Design Stream   |  Maxsurf   |  News..!   |  SITE MAP..!   |  Site Search   | Design Team   |  Contact Us Please see the  AVAILABLE BOAT PLANS web page

Sailing Yacht Designs by Kasten Marine Design, Inc. Copyright 2016 Michael Kasten Updated June 2016   The sailing yacht designs listed below are arranged in order of their size, from the largest at over 164 feet (a traditional plank on frame wooden ketch) to the smallest at 8 feet (an aluminum sailing pram). New boat designs are added as they are developed (marked with the symbol) so you may want to bookmark this page and check in periodically... Please also have a look at our Prototypes page to see a number of new designs that are currently being developed or imagined.   Ordering Study Drawings; Estimating Plans; Building Plans The majority of the designs listed below are available as Stock Designs, or are offered at a substantial discount versus the cost of developing a new Custom Design.  For each design listed below, there is a link to a web page describing the design in detail.  If more information is desired in order to start planning for construction, an Estimating Plans Set is available which includes a Structural Profile and Arrangement plus a complete Vessel Specification and a comprehensive Equipment List, all of which are essential aids for planning. The intent of the Estimating Plans Set is to provide enough information for any builder to give a firm estimate for construction of the vessel. Building Plans contain all the information actually needed to complete construction of the vessel. If you would like to order Study Drawings, Estimating Plans, or a complete set of Building Plans for any of these designs, please see the Plans List Page for additional detail, a summary of plans prices, and complete ordering information. See our Stock Design Page for a thorough description of what is included in a typical plans package. If you want to know what's involved in creating a Custom Design to suit your specific requirements, you'll find excellent detail on our Custom Design Page .    Large Sailing Yachts As yachts, these larger vessels provide the height of luxury on the water, with ample space for an extended family or for chartering.  These yachts are second to none... The 38m Pinisi AMANDIRA pictured above has been featured in many yachting magazines as well as Architectural Digest.  Our 36m Pinisi Silolona has has won accolades in SE Asia Yachting as the best newly built sailing yacht in Asia in 2004, the year of her launch; and has achieved cameo appearances in Vogue magazine, the New York Times; La Figueroa, Time magazine, plus many yachting magazines.  

50m Indonesian Sailing Pinisi - The 36m Silolona was the inspiration for this much larger Charter Pinisi.. At 50m (164 feet) there is ample room for luxury chartering throughout Indonesia with occasional forays to Malaysia, Thailand, the Andaman Islands and the Maldives. Designed to the structural standards of Germanischer Lloyds, this vessel will offer superior security, luxury and comfort. For more information about this design or other traditional wooden vessels, please inquire .

38m Sailing Pinisi, AMANDIRA  - A 38 meter (125 foot) luxury wooden sailing yacht for occasional chartering, having deluxe accommodations for the owner, private staterooms for 8 additional guests, plus accommodation for 14 crew including dive master and guide. Designed to the standards of Germanischer Lloyd's for maximum safety and longevity. To be built in Kalimantan Timur (East Borneo). For more information about this design or other traditional wooden vessels, please inquire . Please also see our Plans List Page for a summary of Plan prices.

36m KLM, DUNIA BARU - A 36 meter (120 foot) luxury wooden yacht. This design is inspired by the present-day traditional Indonesian KLM types (motor sailors). The result is a luxury private yacht for occasional chartering, having deluxe accommodations for the owners, private staterooms for 10 guests, plus accommodation for 12 crew. Designed to the standards of Germanischer Lloyd's for maximum safety and longevity, and built in Kalimantan Timur (East Borneo). For more information about this design or other traditional wooden vessels, please inquire . Please also see our Plans List Page for a summary of Plan prices.

36m Pinisi, SILOLONA - Pictured above, the traditionally built Silolona , a wooden Indonesian Pinisi , measuring 36 meters (118 feet) on deck, was built in Kalimantan Selatan (South Borneo) for chartering throughout Indonesia. The intent of this design has been to provide a taste of traveling aboard a traditional sailing Bugis Pinisi, complete with Indonesian crew. Designed and built to the structural standards of the German Lloyd's rule, there is a generous measure of security, luxury and comfort for eight to sixteen charter guests (depending on which interior layout is preferred). For more information about this design or other traditional wooden vessels, please inquire . Please also see our Plans List Page for a summary of Plan prices.

36m Tern Schooner - A 36 meter (118') deluxe wooden sailing yacht. The interior is very open, yet will accommodate two owners, eight guests or family members, and four crew. This design has been inspired by the fast Privateer sailing vessels of yore. As such, the Tern Schooner is designed to perform well under sail. Twin engines provide top performance under power. Structure is according to Germanischer Lloyds throughout. For more information about this design or other traditional wooden vessels, please inquire . Please also see our Plans List Page for a summary of Plan prices.

33m Indonesian KLM -  A 33m (108 foot) charter yacht in wood, sister to the 36m KLM listed above and the 30m KLM listed below. A luxury private yacht that can also be used for charters. Designed to the German Lloyd's rule for wooden ships for maximum structural integrity and long life. For more information about this design or other traditional wooden vessels, please inquire . Please also see our Plans List Page for a summary of Plan prices.

30m Pinisi, SI DATU BUA - Our original 36m Pinisi design has been an inspiration for a series of design studies, each of which share the same traditional aesthetic of the wooden Indonesian Sailing Pinisi. This smaller 30m (98 foot) version is intended for private use and occasional chartering throughout Indonesia. Designed to the structural standards of the Germanischer Lloyds, this vessel will offer superior security, luxury and comfort. For more information about this design or other traditional wooden vessels, please inquire . Please also see our Plans List Page for a summary of Plan prices.

30m Indonesian KLM - This 30 meter (98 foot) luxury wooden yacht is modeled after the present-day traditional Indonesian Kapal Layar Mesin . Literally translated, this means "boat-sail-machine." Although we would call this a "Motor Sailor" these craft are simply referred to in Indonesia as " KLM ." The concept here has been to create a private yacht that can also be chartered, and which has deluxe accommodations for the owner and guests, plus generous cabins for crew. For more information about this design or our other traditional wooden vessels, please inquire . Please also see our Plans List Page for a summary of Plan prices.

Zebulun 96 - Zebulun is a modern sailing yacht in all respects. Intended for fast all-ocean sailing. All aluminum construction; twin fin keels with ballast bulbs; twin rudders; three masts; fully battened sails; etc. The ultimate charter vessel, having nine private staterooms, for a capacity of 18 to 20 all together. Equally capable as a motor sailor or pure sailing vessel. Very impressive!  Please see the Plans List Page for a summary of Plan prices.

Mermaid 61  - A classic Brigantine styled after the 1700's privateers. Planned for commercial use, there is a flexible-use space just forward of amidships that can be used as a 5 ton cargo hold, or a large workshop, as a twin cabin for charters, or as a general use cabin or dining hall for day charters or boutique cuisine evening cruises. Mermaid combines modern materials and a modern hull form with a traditional Brigantine styling that is true to its heritage even down to the carvings. For example, all aluminum or all steel hull construction with all aluminum spars and modern rigging materials. Please see our Plans List Page for a summary of Plan prices. For more information, please inquire .

Shiraz 56 - A a fast aluminum sailing yacht with classic styling in the Herreshoff tradition. Fully detailed for construction in aluminum complete with NC cutting files. Conceived as a motor sailor , with the emphasis on sailing performance. Two separate staterooms, large saloon and galley, even a bath tub! From the shelter of the 'midship cockpit one can watch other vessels fall astern as though they were tied to a coral head... Aluminum spars; ketch rig. If re-designed, wood or fiberglass are also possible (with substantial revisions to the plans). Please see the Plans List Page for a summary of Plan prices.

Lucille 50 - This vessel is in my view a proper motor sailor ! Lucille has a true pilot house, a real walk-in engine room, and private cabins for four. There are two versions, one having the wheel house aft, the other with the house amidships. Lucille has a rounded hull and very clean lines suited to steel or aluminum. If re-designed, wood or fiberglass are also possible (with substantial revisions to the plans). Aluminum spars, schooner rig. Please see the Plans List Page for a summary of Plan prices.

Many more sailing yacht concept designs can be found on our Prototypes web page.    

Mid-Size Sailing Yachts

Jasmine 48  - An all aluminum junk rigged schooner - and a highly capable motor sailor as well! The request here was to design a blue water schooner with an easy to handle rig, a spacious interior and classic styling, then apply modern technology to all of that...! In this case all aluminum structure, free standing rig, electric motor propulsion, and a very comfortable interior. A rounded hull for construction in aluminum. Recently updated to include the concept of having a pilot house aft. If re-designed, wood or fiberglass are also possible (with substantial revisions to the plans). Please see the Plans List Page for a summary of Plan prices.

Redpath 44 - I designed Redpath for myself. Enough said. In my view she is simply beautiful. The idea was to create a simple and comfortable live aboard schooner for two. When left to my own devices, herein lies much of my preferred design approach. Though designed as an auxiliary sail boat, Redpath is also a true motor sailor . Aluminum spars, schooner rig. Hull construction in steel. If re-designed, wood or fiberglass are also possible (with substantial revisions to the plans). Please see the Plans List Page for a summary of Plan prices.

Redpath 44 - Okay, why is Redpath listed twice here...? We recently completed a conversion of the Redpath design to aluminum construction, including aluminum spars. We also completed new NC cutting files for aluminum construction (imperial dimensions). If re-designed, wood or fiberglass are also possible (with substantial revisions to the plans). Please see the Plans List Page for a summary of Plan prices.

Highland Lass 42 - Grace's big sister. A classic rig on the finest of single chine hull forms intended for steel or aluminum construction. Designed for performance cruising. Comfort for four. Luxury for two. Aluminum spars, schooner rig. If re-designed, wood or fiberglass are also possible (with substantial revisions to the plans). Please see the Plans List Page for a summary of Plan prices.

Benrogin 40 - A transom-stern rounded hull and clean lines ideally suited to steel, aluminum, fiberglass or plank on frame wood construction. Intended for family cruising. Two versions: one with a wooden deck for luxury, the other having a metal deck for simplicity and ultimate strength. If re-designed, wood or fiberglass are also possible (with substantial revisions to the plans). Please see the Plans List Page for a summary of Plan prices.

Greybeard 38 - A variation on Fantom. More displacement with a different interior and a slightly different look. Every bit the boat to live up to her name. With a rounded hull and easy lines Greybeard is ideally suited to steel or aluminum. If re-designed, wood or fiberglass are also possible (with substantial revisions to the plans). Aluminum spars, cutter rig. Please see the Plans List Page for a summary of Plan prices.

Fantom 36 - A round bottom double ended cutter in the Archer tradition. With a rounded hull and easy lines Fantom is ideally suited to steel or aluminum. This boat was designed for ultimate conditions with the intent to make the Northwest Passage. Aluminum spars, cutter rig. If re-designed, wood or fiberglass are also possible (with substantial revisions to the plans). Please see the Plans List Page for a summary of Plan prices.

Grace 36 - Can a metal boat have grace? Absolutely yes! One of the prettiest metal boats afloat, and a very easy shape to build. Designed for ocean voyaging in style. Aluminum spars, ketch rig. Hull construction in steel or aluminum. If re-designed, wood or fiberglass are also possible (with substantial revisions to the plans). Please see the Plans List Page for a summary of Plan prices.

Many more sailing yacht concept designs can be found on our Prototypes web page.  

Pocket Size Sailing Yachts

Bedouin 28 - An excellent bilge keel yacht, the big sister to Sarah Cat. Trailerable and ocean worthy. Aluminum spars, cutter rig. Hull construction in aluminum. If re-designed, wood or fiberglass are also possible (with substantial revisions to the plans). Preliminary drawing available; please inquire .

Sarah Cat 23 - A centerboard boat with a classic fantail stern. Tabernacle mast for easy trailering. The most economical of cruising boats. Aluminum spars, cutter rig. Hull construction in aluminum. If re-designed, wood or fiberglass are also possible (with substantial revisions to the plans). Please see the Plans List Page for a summary of Plan prices.

Larger and smaller preliminary designs in this size range can be found on our Prototypes web page.   

Yacht Tenders

The Pram - The pram hull form has the most carrying ability within the least length. Being flat bottom, these sailing prams take the beach gracefully, and they are easily stowed. Sizes range from 8' to 14' with construction in aluminum, plywood or fiberglass. Please see the Plans List Page for a summary of Plan prices.  

Please see the  AVAILABLE BOAT PLANS web page. Home   |  Intro   |  Our Design Process   |  Stock Design Info   |  Motor Yacht Designs   |  Sailing Yacht Designs   |  Prototype Designs Plans List   |  Articles   |  Our CAD Design Stream   |  Maxsurf   |  News..!   |  SITE MAP..!   |  Site Search   | Design Team   |  Contact Us

• All Web Site Graphics, Layout, and Written Content at this Domain Created by Michael Kasten.
• All Graphic and Written Materials at this Domain Copyright © 1989 - 2023 Michael Kasten.
• All Content Registered with US Library of Congress and US Copyright Office.
• Copyright Violations will be Prosecuted. All Rights Reserved.

Attainable Adventure Cruising

The Offshore Voyaging Reference Site

• Sailboat Deck Layouts

I’m going to use the Outbound 46 as a base to write about optimal deck layouts for sailboats. Information that will help anyone to either select a good deck layout when buying a boat, or fix a screwed-up one on a boat they already have.

Good Deck Layouts Are Rare

That last sentence may surprise many since it would be logical to expect cruising sailboats to have good and functional deck layouts, but as an ex-sailmaker and longterm racer, the thing that never ceases to amaze me is that most boats, particularly those marketed as cruisers, come out of the yard with the rig and deck gear set up so poorly that actually sailing them is nothing but a huge chore, and it takes years for even a knowledgeable owner to sort things out—just read Colin’s trials and tribulations with the rig on his Ovni 435 to see what I mean.

This is so bad that I’m pretty sure that the popularity of in-mast and in-boom mainsail furling systems is in large part because most boats are so poorly set up for reefing that owners have been scared off simple and robust systems and toward complex, fragile, and expensive ones.

I will also write, once more, about speed. I know, we are cruisers, so why do we care? Well, up to you, but to me if we are going to really cruise under sail, rather than just motor around with an oversized flag pole and occasionally unroll a sail attached to it as we see so often these days, we might as well do it properly.

Seriously, a well set-up boat, efficiently reeling off the miles under wind power alone, is one of life’s sublime pleasures, and knowing that we can control the rig and shorten sail quickly and efficiently without automation or brute strength is the cherry on top.

Let’s look at how to do that:

Login to continue reading (scroll down)

Please Share a Link:

More Articles From Online Book: Sail Handling and Rigging Made Easy:

• Six Reasons To Leave The Cockpit Often
• Don’t Forget About The Sails
• Your Mainsail Is Your Friend
• Hoisting the Mainsail Made Easy—Simplicity in Action
• Reefs: How Many and How Deep
• Reefing Made Easy
• Reefing From The Cockpit 2.0—Thinking Things Through
• Reefing Questions and Answers
• A Dangerous Myth about Reefing
• Mainsail Handling Made Easy with Lazyjacks
• Topping Lift Tips and a Hack
• 12 Reasons The Cutter Is A Great Offshore Voyaging Rig
• Cutter Rig—Should You Buy or Convert?
• Cutter Rig—Optimizing and/or Converting
• Cruising Rigs—Sloop, Cutter, or Solent?
• The Case For Roller-Furling Headsails
• The Case For Hank On Headsails
• UV Protection For Roller Furling Sails
• In-Mast, In-Boom, or Slab Reefing—Convenience and Reliability
• In-Mast, In-Boom, or Slab Reefing —Performance, Cost and Safety
• Making Life Easier—Roller Reefing/Furling
• Making Life Easier—Storm Jib
• Swept-Back Spreaders—We Just Don’t Get It!
• Q&A: Staysail Stay: Roller Furling And Fixed Vs Hanks And Removable
• Rigid Vangs
• Building A Safer Boom Preventer, Part 1—Forces and Angles
• Building A Safer Boom Preventer, Part 2—Line and Gear Strength Calculator
• Downwind Sailing, Tips and Tricks
• Downwind Sailing—Poling Out The Jib
• Setting and Striking a Spinnaker Made Easy and Safe
• Ten Tips To Fix Weather Helm
• Running Rigging Recommendations—Part 1
• Running Rigging Recommendations—Part 2
• Two Dangerous Rigging Mistakes
• Rig Tuning, Part 1—Preparation
• Rig Tuning, Part 2—Understanding Rake and Bend
• Rig Tuning, Part 3—6 Steps to a Great Tune
• Rig Tuning, Part 4—Mast Blocking, Stay Tension, and Spreaders
• Rig Tuning, Part 5—Sailing Tune
• 12 Great Rigging Hacks
• 9 Tips To Make Unstepping a Sailboat Mast Easier
• Cruising Sailboat Spar Inspection
• Cruising Sailboat Standing Rigging Inspection
• Cruising Sailboat Running Rigging Inspection
• Cruising Sailboat Rig Wiring and Lighting Inspection
• Cruising Sailboat Roller Furler and Track Inspection
• Download Cruising Sailboat Rig Checklist

Hi John I could not agree with you more about how frequently boats with conventional mains are poorly set up for easy reefing and eventual dousing. It is another area where the maritime media/boatbuilders etc. have dropped the ball at educating owners how best to have their boat set up. Too many sailors (and their crew) get put off by a poor and difficult reefing set-up which likely means they have put off reefing and been over-canvased needlessly: always a lousy thing. Enough of that and they are buying a cabin in New Hampshire. I urge those looking at in-mast or in-boom furling to consider that reefing and dousing the main can be easy and fairly fast and with a minimum of effort on a boat that is well set up for it. I then enumerate the myriad down-sides of particularly, in-mast reefing/furling and the benefits of a conventionally rigged main. I am in no way a speed demon, but I like to sail and I like to sail well. You mention sublime pleasure in cranking out miles: my sublime pleasure often comes at watching superbly shaped sails at work; especially when in challenging weather, the third reef is in and working and that small sail is perfectly shaped to do its job and as bulletproof in functioning as can be devised. My best, Dick Stevenson, s/v Alchemy

I agree completely, particularly on the pleasure of looking at really good mainsail shape when reefed.

Hi John, I totally get your “simplicity” approach and at mast mainsail handling preference. It just wouldn’t work for us and I suspect for many other cruising couples. I think I can see at least one hatch in the Outbound 46 hard-dodger top, which means adjusting the halyard / reefing lines and setting the mainsail / twist, should be simple enough from the cockpit, if (big “IF” I know) the reefing lines are well set-up. And I personally like this set-up for short-handing. Our safety process requires a second crew to be in support, if someone leaves the cockpit (day or night, coastal or offshore). I would guess we could reef / shakeout a reef on the Outbound 46, without calling the off-watch crew – a real-plus in our book as we mostly sail two-up. Our first mate would not cruise with me if I left the cockpit every time we needed to take a reef in rough conditions. It’s that simple. And if something happened to me, there is no way she would go forward to the mast and handle the sail on her own. Whereas she can, and does, reef single handedly on our boat, and I would guess she could on the Outbound 46 set-up, which is almost identical to our boat – the difference is we have in-boom furling which simplifies operations further. Likewise, the outbound 46 set-up would be easy and safe to hoist / lower / reef the mainsail when single-handing. I see so many single-handing yachts sailing just with their headsails, I suspect because on-mast mainsail handling leaves no one in the cockpit, if something happens. I often single hand our yacht with no loss of efficiency and really enjoy it. Br. Rob

I just can’t see that twisting ones head to look up out of a small hatch to see the mainsail while simultaneously grinding a winch and operating clutches is ever going to provide the visibility and situation awareness of looking directly at the part of the sail you are tensioning while standing at the mast while right next to the luff where any hang ups can be quickly seen and dealt with. So yes, for sail trim the hatches may help a bit, but not for reefing. Also at night on the Outbound a headlamp will reflect off the hatch glass making visibility of the main effectively zero.

I agree that being able to reef and shake out without calling the off watch is vital, but we do that fine at the mast too. Phyllis and I are also not fans of the idea of calling the off watch every time someone leaves the cockpit since we feel that the disruption of rest outweighs and added benefit of so doing.

I guess that relates to our basic thinking that the deck, particularly as far as the mast is not an intrinsically hazardous place to be avoided, but simply part of the working area of the boat, just as the cockpit is. We feel that regularly visiting the mast in all weathers is vital since it will be required anyway for functions like setting a proper preventer, setting the pole, and moving the runners forward, not to speak of clearing any kind of SNAFU.

We also differ in that we evaluated in boom furling/reefing and rejected it as too fragile, difficult to fix at sea, and expensive for our needs. That was based on experience in that the boat I did was on for six weeks as guide on a trip to Greenland had one.

So, in summary, I guess we just see things in a fundamentally different way.

Like you I mostly sail singlehanded or effectively singlehanded and I don’t really regard going forward in a rising wind as a pleasurable experience, especially in the dark. I’d like to add granny bars at the mast but worry that they would be extra deck clutter and spoil “the look”. But I’ve got to say I’m with John on this one. There’s quite enough string in the cockpit already without adding seven more bits. And, while in boom furling does look attractive, for me its too reminiscent of the appalling old rotating boom mainsail furling system I had on my first yacht, a Folkboat. The sail shape one got on that in any but perfect conditions was sad to see.

The sailor who puts in an early reef is a happy sailor. And probably longer living. How often is one surprised at the improved performance that results from under-pressing the rig ? And, while there is a lot that can lengthen the time at the mast putting in a reef, shaking an unnecessary one out really is a matter of seconds.

In defence of modern in boom furling, the set is way better than it was in the bad old days of roller reefing mainsails. That said, my big problem with them is complexity and fragility. Probably fine for inshore sailing where if they break you can just take the main down and head for somewhere to wait for parts and with smooth water where you can fix it, but I would never take one offshore, and particularly not to the high latitudes. All this based on taking a yacht to Greenland with one.

I own a Outbound 46 hull#50. Would add the following. The hydraulic backstay is quite helpful reefing the Genoa. Put tension on that stay and she rolls up more easily. Unless you tune the rig with more tension on the solent stay then the Genoa stay when the backstay is untensioned you get headstay sag on the solent. You lose nothing upwind using the solent instead of the Genoa going upwind so the need to roll up the Genoa before tacking is a non issue as it ends up being a reaching or running sail. We stand single watches. I love having both the primaries (powered) and the headsail reefing lines an arms length away from the wheel. I can reef under control, by myself with no engine nor AP. Then go forward and deal with reefing the main. I can do it under Hydrovane. Not needing to bring anybody up from below is wonderful. I hate single line reefing on any boat. It better than in boom or in mast but not by much. If done get a Dutchman as well. That makes it easier to inch the main down and have both ends of the sail tension correctly as you can see what’s going on and the sail has no choice but to fold correctly. Outbound come single for first two and double for the third. Would think to get just two very deep reefs and make both double. I have the survey being done on Tuesday. Then she’s gone as we transition to a Norhavn. The Outbound is the best mom and pop blue water cruising boat there is imho.

I too am not a fan of single line reefing so I think your recommendation to go with two deef reefs each with two separate reefing lines would be a good one.

That’s how we went, but then as a comparatively heavy motorsailer, we tend to leave the full main up a little longer than some just to make the boat go. We have separate reefing lines, as well and have all halyards and related lines at the mast. We have preventers, staysail sheets, yankee jib sheets and occasionally, spinnaker sheets back to the winches (three pairs) in the aft cockpit position, where there is also end-boom mainsheeting (6:1) and a strong Garhauer traveller (3:1). Works for us to date. I have over the years become a touch suspicious about “convenience” unless the sea first makes its case.

I agree was many of your points and know by your article I am not going to convince you, but we love being able to put in and take out reefs in from the cockpit. We can easily put a reef in or shake a reef out in less than a minute on our 37 foot cruising boat. I have read Colin’s article and I think a single line for each reef is way too much friction. We use a second line to pull the tack into the right position at the goose neck. These lines on our boat are only 5/16. Each one is led from the reefing hook, through the reef tack crinkle to a carefully placed bullseye on the mast, through a pulley at the mast base and then back to a harken cam cleat next to my jammers. You never need to put this on a winch – the idea is to get the bullseye position such that you end up with the reef crinkle pulled into the goose neck at just the right position when the halyard is re-tensioned. The clew end is conventional – from a bowline positioned about 6 inches aft of where you could stretch out the foot of the sail at the reef point up through the reef clew cringle to pulleys at each end of the boom through a good block at the base of the mast and then to a jammer and winch at the cockpit. When putting in a reef we pull down on the tack line while easing the halyard. Don’t allow slack in the halyard – the jammer is cast off but the halyard is restrained by hand with a single turn around the winch. 2 or 3 times we will pause in this operation by locking the halyard jammer and pulling the slack out of all the other tack and clew reefing lines by hand. We have found that this is the secret to being able to complete the whole operation from the cockpit since minimizing slack loops prevents them getting caught up anywhere. We continue until the halyard is just past a mark on the halyard line and then put the tack line in the cam cleat. At night we shine a flashlight on the tack to make sure it is neatly pulled into the gooseneck and then tension the halyard on the winch. Once again take the time to take all the slack out of the other reef lines by hand. Put the clew reefing line on a winch and crank until you are happy with the foot and leach tension – you need to check this with a flashlight at night.

Our reefs can be put in in way less time than it takes to write about it quickly and safely from the cockpit without even having to put your jacket on. Because we can put in or shake out reefs in the main easily we do not procrastinate for a moment about reducing or increasing mainsail. Our record is 11 changes in a single 3 hour shift as a series or 20 minute squalls rolled through at night close to the equator on a passage from San Francisco to the Marquesas and the lone watchkeeper was busier than a one armed paper hanger reacting as the wind went up and down from 8 to 30 knots!

Sounds like a good system. And I agree that taking the slack out of the non-loaded reefing lines as you reef is important. We do the same at the mast.

Really glad to see you giving the Outbound a thorough look, John!

Having cruised full-time aboard an Outbound 46 from 2017–2019 (we no longer own the boat), I can report that the main halyard and reefing setup works exceptionally well. The only annoyance was, as you pointed out, somewhat poor ergonomics crouching under the dodger (I’m 6’3″). The dodger hatches are perfectly positioned (like everything else on the Outbound) so you can actually see the main while hoisting, reefing, and trimming.

I saw your response to Rob about working at the mast. I agree that the side decks and mast are “part of the working area of the boat”. On balance, considering all the factors, reefing from the cockpit gave us (my wife and me) more flexibility and more peace-of-mind than reefing at the mast, which we did on our previous boat (a Sabre 38).

Aside: I also appreciated how cockpit reefing lowered the behavioral “friction” of making the decision to reef. Leaving the cockpit (with all associated precautions) just feels… harder than staying in the cockpit. Reducing sail at the right time is one of the most critical components of safe and comfortable cruising, and I was glad I never had to “think twice” because I didn’t want to deal with leaving the cockpit. Perhaps that’s irrational, but so are we all 🙂 I think of it as behavioral systems engineering.

Interesting point on “behavioural” friction. It’s not a problem we have ever suffered from, probably because I actually like “ deck sports ” and as a ex-racer and sailmaker I can’t stand being under or over canvased, but I can certainly see that it could be an issue, particularly for people who have been subjected to poor deck layouts and therefore regard reefing as a huge chore, no matter how they do it.

That said, I think that this “behavioural friction” is something we should all work on overcoming and not give into or modify our boats to pander to it. In my experience, not getting out on deck regularly can lead to all kinds of problems, particularly being lazy about rigging proper preventers and generally checking things over from bow to stern at least twice a day, more often in heavy weather.

Don’t get me wrong, if you find in cockpit reefing works for you, that’s fine, it’s your boat, but if that leads to rarely leaving the cockpit for other vital functions, then I think it’s a mistake.

Perfect timing John.

After six weeks of hard work my right now my deck is a perfectly clear expanse of white. Almost literally a clean sheet of paper. (So far 60 litres of Jotun epoxies with another 16L of Hardtop AX to go.)

Up until this point I my general for the deck layout was heavily influenced by the majority opinion I kept encountering locally which was to run all the mainsail controls back to the cockpit. But because there is a major step in our coachroof which forces two 30 deg turns in all the lines, I was always a little apprehensive on friction. So after reading this article (and a similar one from Peter Smith) I’m inclined to follow your advice.

All my halyards can readily stay at the mast, but moving all the other mainsail lines, the reefs, topping lift, outhaul, cunningham and vang back to the mast creates quite a traffic jam around the base of the mast. Any hints on how best to organise particular brew of spaghetti?

The key to keeping that spaghetti organized is to keep all the reefing and outhaul lines on the boom, rather than lead them down to the deck. We have an article on that with photos here: https://www.morganscloud.com/2010/11/19/reefing-a-sailboat/

Note that since I wrote that, we changed from jammers to clutches.

The vang control is the exception to my rule, and should be lead aft to the cockpit. Or, on boats over about 30,000 lbs a hydraulic vang with control in the cockpit is a good solution.

Hi John and all, I was not going to wade in on this, but wish to underline a couple of points and make a suggestion. In my estimation, getting rid of friction is a safety issue and not merely convenience, in part because friction (among other things) causes skippers to hesitate doing the right thing. This is the case for a racing boat with strong crew, but far more the case for a cruising couple. Also, friction might mean that a job does not get done well: say a sloppy reef that hurts the sail and degrades sail shape and sailing efficiency. Finally, to often I suspect the push for electric winches etc. is a result of poor design and unnecessary friction in the system. An example is the retrofit of an electric main halyard winch before one installs slippery mainsail track (as well as adding low friction blocks that may be in the system). Getting rid of friction has a good start with slippery mainsail track and low friction blocks and wise design. Few boats are offshore ready as built/designed which is a shame as it is a subsequent expense in $$ and time that is not necessary. And we all like to think our boat is good-to-go from the get-go so it is hard to immediately replace new items. It would not be hard for manufacturers to get it right from the get-go at little additional expense. Slippery track allows one to raise the main almost the whole way from the mast if design allows for full body stretch to get your whole weight into play. This changes a few minutes winching “ordeal” into a few seconds exertion followed by a few turns by winch handle to tension: easily done whether at the mast or under the dodger. This is convenient and fast, but not necessarily a safety issue. The safety aspect comes when reefing is done easily and without hang-up, when reefing/dousing is accomplished going downwind in a breeze, and when dropping the main and it comes down like an express train. My boat came with in-cockpit reefing (1st 2 reefs with the third reef downhaul done at the mast) and we have made it work and like it: in part because either of us can quickly and efficiently do the first 2 reefs alone from the cockpit whereas going on deck at night in boisterous conditions, we wake the off-watch. (We do “deck tour” inspections at change of watch when both of us are awake and kitted up.) Reefing from the cockpit, for us, takes a good deal of prior preparation at the onset of the season: mainly ensuring that line markers are in the correct place on all reef lines and halyard for each reef. This gets us very close to a good reef, but sometimes takes a bit of fine-tuning as things settle down and stretch out as the sail fills. This is easily seen from the cockpit and is accomplished by tweaking the reef/halyard lines from the cockpit. As to the spaghetti that is so often mentioned as the major downside of in-cockpit reefing, our solution is to snake all “tails” down the companionway. This is only done when reefed down and accumulating lines. On Alchemy, this could be (when deeply reefed and using all lines for adjustment) up to nine lines: 2 reef downhauls, 3 reef outhauls, 1 halyard, 1 main sheet, and 2 traveler lines. (Sounds terrible, doesn’t it!) These tails then reside comfortably on our engine box ½ way down to the floor or, at times, on the floor next to the bottom step. Lines, stored in this manner, are always good to go without tangles or the need to uncoil and ensure they run free. The lines, being lead next to and held to the sides of the ladder, never interfere with safe access to the steps. There are times, of course, where we wish to close up and when that occurs, we can do so with the washboards in and the hatch mostly closed. Those fortunately rare times where we wish to be fully closed up, securing the tails in the cockpit so they are not in the way, but ready to be worked takes a bit of work, but is no big deal. I suspect not all companionway designs lend themselves to this solution, but it has worked a peach for us for decades, and may help with the “spaghetti” mess for some boats where cockpit reefing is chosen. My best, Dick Stevenson, s/v Alchemy Ps. It has not been mentioned, I believe, but I would guess that the size of one’s boat may play a part in the choice/comfort level of going on deck in boisterous conditions. Bigger boats are just a lot more stable and predictable in their motion, smaller boats livelier and quicker to react to a wave slap or wind burp.

I totally agree on adding a slippery mainsail luff track. Adding ours a few years after we bought the boat is definitely the change we have made with the largest benefit.

Great. I’ll implement that. I hadn’t thought of double ending the reefing lines so that you can work from both sides.

I’ve also had a good yarn with a local with a very similar boat and 30 years of continuous live on the boat experience. He made an interesting observation on the lines led aft vs at the mast debate; his decision point is ‘if you an offshore sailor then reef at the mast’. His reasoning is that the longer passage the more likely something will go wrong, the more important it is you are well accustomed to leaving the cockpit in adverse conditions. And that applies to the whole crew. At the same time he acknowledges there is no absolute answer, that like everything else the decision is a compromise, and others will lead the lines aft for reasons that work for them.

He backs this up with good lifelines and a solid mast pulpit. Both of which I’m going to implement as well as per your articles in the past.

Thats an interesting way to look at the decision. But the more I think about it the more I worry that the trend to aft lines combined with cockpit enclosures is producing a generation of sailors who regard the deck as a scary place to be avoided, which I think is a very worrying trend. I have an article brewing on that.

That said, I’m sure there are sailors who are comfortable on deck and have the lines lead aft, which is all good.

Point being that I’m pretty sure that not going out on deck regularly is actually more dangerous than doing so.

Hi John, You write: “Point being that I’m pretty sure that not going out on deck regularly is actually more dangerous…” Good point. Take, for example, the learning curve for working the boat with harnesses attached so as to not get tangled or so frustrated as to unclip. If this is not done with regularity, such as during regular deck tours, then it will be more difficult when it comes to needing to work the boat in boisterous conditions. Or using the deck tour time to find handholds when heeled over 15-20 degrees so that your hand knows instinctively where they are at night with spray in your face. My best, Dick Stevenson, s/v Alchemy

The cockpit enclosures bother me. Particularly in our tight, high-traffic waters, I think they take away too much visibility and too much situational awareness. Three times out of four, if I have to take evasive action despite being the stand-on vessel, I’ll notice a full cockpit enclosure on the boat (power or sail) that didn’t see me.

We actually took our soft dodger down entirely last week and are finding that, in our local conditions (where waves do *not* break over the deck), the extra visibility is way more valuable than the shelter.

All lines led aft often makes for a real mess of spaghetti (read: tripping hazard) around the companionway. Trip-and-fall is, IMHO, likely a bigger risk than slipping overboard from the deck. I’m surprised by how many designers & builders think that a line just ends at the winch, and forget about the 50 feet hanging off beyond that. (It’s an issue at the mast, too; a lot of boats seem to have no good place to put coils of excess halyard, reefing line, etc. once the lines are tensioned.) I also see a lot of boats with no good places to clip a harness tether or rig a jackline, and am starting to think that this particular issue needs to be addressed at the “textbooks and engineering design standards” level.

I agree on the dangers of cockpit enclosures. The boat that nearly hit me last summer was being run from a totally buttoned up cockpit enclosure: https://www.morganscloud.com/2019/08/24/dont-alter-course-to-port/

That said, I think that cockpit enclosures can be used safely, like most things, as long as we keep them open when we should so we can see and hear.

Bottom line, buttoned up cockpit enclosures are just another manifestation of the fundamental problem: putting comfort ahead of safety.

I wonder if it’s partly related to the boat’s seakindliness. A large, long-for-its-displacement yacht like MC has a much gentler action at sea than a lightweight, beamy, modern, race-inspired, accomodation-maximised-for-LOA “cruiser.” Leaving the cockpit in a small light boat is a lot scarier than doing it on a large heavy one.

You might be right, but the Outbound 46 would not fall into that class.

Also, my thinking would be don’t own a boat, at least for offshore sailing, that scares you so much that you don’t want to leave the cockpit.

Regarding backstay tensioners – I am pondering my head how to handle twin (not split) backstays. For split backstays you might use a tensioner car as you had linked to, but this will not be possible for twins. I notice that MC has twin backstays, how did you set it up to allow symmetric tensioning/slacking them?

The best solution is two hydraulic rams plumbed to the same pump. Set up this way, they automatically equalize tension between the two stays.

John, thank you for teaching us North Americans a new phrase today “poor diddums”,I like that.

As a retired rigger, if is even possible to be one, I could not agree with you more on not leading everything back to the cockpit. Very expensive and all that hardware sends friction through the roof. Just leave it on the mast where it belongs. My customers would say, but it’s not safe to go out of the cockpit at night or when the wind starts kicking up. If it’s not safe to leave the cockpit, you need to make it safe to leave the cockpit. You need a good Jack line system such as the one you described. You need a good hand holds so no matter where you are on deck there is something to hold onto. Solid hand rails rather than stanchions and wire. Best if you don’t have to bend over to find them. Handrails that when you stick your hand out that’s where they are. At the very minimum some kind of a deck edge so you don’t go sliding off the deck, bulwarks are even better. Mast bars that allow you to wrap a leg around to free up both hands are a great addition.

When it comes to hoisting the mainsail, or reefing it. A low friction system is the only way to go.. Finally broke down put a Harken bat car system on including bearings on the intermediate slides. Easy to raise the main, very easy to reef. Does not matter what the wind direction it is when reefing. Mark the reef points on the halyard with whippings so that you can feel them in the dark. It’s always a chore when you drop the sail a lot farther than you needed to. Only to have to winch it back up when it’s full of wind.

The photo of the mast base turning blocks illustrates one of my little pet peeves. The shackles are not safety wired. After having the main sheet blocks, come adrift from the traveler one day, thankfully in light air. I safety wire every shackle not taken on and off on a regular basis. Including roller furling headsail shackles.

I could not agree more!

And I agree on shackles too. That said, for roller furlers and the like I have had good luck with the self locking shackles that have little flats on the non-threaded side of the pin hole that stop the pin backing out.

Hi David and John, And I have had good luck with a little dab of silicone on the threads. I don’t like sharp wire ends about near sails or where line can be dragged over them like at the base of the mast. It is arguable that my skill at tucking them out of trouble could use improvement. Dick Stevenson, s/v Alchemy

Hello John! I have enjoyed reading your many articles over the past few years. This deck layout one is an excellent discussion and observations. I went through the same process several years ago before purchasing a new boat. I settled on an X-Yacht Xc38 with a John Mast. It has an outstanding deck layout whereby we sail short handed all the time and I have sailed in several long distance single handed races with some horrible weather. I have added inboard jacklines which increases safety when going to the mast (very infrequently) or the foredeck when hoisting the asymmetrical spinnaker or Code 0. I installed a rope clutch on the mast for single handed hoisting of the spinnaker and Code 0 sails. We did put an electric winch for the mainsail halyard! It is a well made offshore cruiser/racer.

Hi Stanley,

I have long been a fan of X-Yacht. Looks like a really fun boat.

I do like lines and halyards at the mast for many reasons explained here. My vintage Tartan 40 has everything except jib halyard led to cockpit. A tides marine track allows me to hoist main to nearly masthead from cockpit. And better yet, a clam cleat installed on mast a few feet below the main halyard exit allows me to even more easily hoist main from the mast, place halyard in clam cleat, and then pull in slack and tension from cockpit. Clam cleat releases and stays well clear once line is led through sheaves. For my use this is enough of a “best of both worlds“ compromise that I won’t go through trouble of moving winches and lines. And I do like being able to drop main from behind dodger in a squall into the cradle cover. I recommend everyone with aft led main halyard at minimum install the clam cleat as it greatly improves ease of raising main particularly with lazy jacks.

Hi Michael,

That sounds like a good idea.

The debate of cockpit versus mast based reefing is an interesting one.  In the compromises of boats, our boat came with everything done from the cockpit and it would be very difficult to retrofit to mast based reefing so I have never really considered it.  This works okay for us as the loads are relatively light due to being a smaller boat and we do not have a big enclosure so vision is not overly impaired (the boat came with a full cockpit enclosure that didn’t even feel safe for motoring so it has never been used).  Like Dick mentions above, we send reef line tails down the companionway in most conditions and it works well.  To me, the best part about this setup is that it is safe and easy to reef with a single person on deck when there are lobster pots around preventing long absences from the autopilot controls.  I suppose that you could get an autopilot remote and bring it to the mast but in the cockpit, it is easy to hit a course change on the autopilot in the middle of reefing.  One other thing that I like is that I can get the jib down (hank-on) into a position where it is secure enough for a little bit while steering simply using a downhaul that is led aft, this is super helpful coming into harbors.

If we had our boat setup as a primarily offshore boat, I suspect that I would prefer to do everything at the mast and of boats that I have sailed on, generally the ones done at the mast are better.  The issue with pot buoys would go away and the clutter in the cockpit would be a bigger deal.  Similarly, the position of the primaries may well be dictated by what the boat is being used for.  Offshore, most people don’t hand steer and there tend to be very few people on the boat making forward in the cockpit a good option.  Coastal, many more people will be hand steering and there are often people sitting in the way of winches that are further forward.  Our boat actually has the winches further forward and when sailing solo, I would strongly prefer having them aft.  It is especially the case when short tacking somewhere when I end up steering with 1 foot so that I can reach both the wheel and the winch, otherwise I would need to use the autopilot which is not my preference (I know that I am weird on this one, even offshore I hand-steer whenever we are sailing and there aren’t other things requiring attention, I suspect this comes from growing up on boats without windvanes or autopilots).

One thing I didn’t see discussed with lines led aft is what it does to winch ergonomics.  I find that I have no problem hand hauling up the main most of the way on up to mid 40’ers with lines led aft assuming that you can stand back behind the dodger and not be hunched over.  The problem comes once the winch gets involved.  The ergonomics under a dodger tend to be terrible and in many cases where the dodger was not part of the original design, you can’t even get a full rotation on the winch handle.  If you were able to raise the sail most of the way by hand, then this isn’t a huge deal.  After one of the discussions on this site in the last year, we procured a ratcheting winch handle and it makes this much better, thanks for pointing those out.  Where it gets really bad is sending someone up the mast.  I have sailed on boats where cranking a 125lb person to the top of the mast completely wears out a big grinder type due to the poor ergonomics.  On our own boat, if my wife is going up, I use the halyard winch as a turn of direction and crank her up with a primary.  If I am going up, jumaring is the name of the game provided that we are in a calm enough spot.  With halyards at the mast, I find all of this a ton easier.

And I agree with all of the other parts of the article too.

A good analysis, as usual. By the way, I did mention the problem of winch ergonomics in the post, although not as clearly as you did:

Worse still, on the Outbound we will be forced to bend down by the hard dodger—this is an ergonomic nightmare. The result of all this inefficiency is that the main must be ground most of the way up on a winch, which makes an electric halyard winch near-mandatory.

As to winch position, as you say it depends on how often you steer. That said the Outbound does not make sense to me since when steering the mainsheet is way too far to reach (under the dodger), and when not steering the jib winches are a ways from both the mainsheet and the dodger. To me an idea short handed set up is so that one can reach both main and jib sheet winches from whatever our preferred position is. Been thinking about this a lot for our next boat which we will be sailed inshore a lot, steering more, and quite often single handed.

Hi John, Sorry, I had missed that your statement included winch ergonomics the first time around.

If you are short tacking up a channel, then having the main winch less accessible is fine but for other changes, you are right that having the mainsheet nearby is helpful.  What we do which isn’t perfect is to play the traveler which I can control from behind the helm thanks to long tails but this requires a long traveler with low loads and even then, once you get to broad reaching, you need to use the sheet and you need to use the sheet if you want to change twist.  The other thing to keep in mind that I can think of is what you are doing during a chicken gybe where having a single person handling all sheets can sometimes be problematic.  On smaller boats, I often find myself standing at the wheel, mainsheet in hand with 1-2 turns on the winch.  Once you practice a bit, you can get really reliable at flicking a turn off from 10′ away provided there isn’t too much load on the line, putting another on is also doable but I find it sometimes takes multiple tries.

I could not agree more about having two sets of tracks for headsails. We have inboard and reaching tracks for our working jib, staysail and storm jib. The one thing that has always had me see the dollar’s flying off the sails was when changing from one track to the other or when adjusting our pin cars.

While building our steel boat, I really wanted to use the adjustable cars, but they were too expensive at the time. All of this while working full time and raising a family. Then there was the epiphany one day a month ago. I took a piece of 6mm spectra cored double braid 2 m long. Stripped off 60 cm of cover off. Spliced in a 6 cm eye in. Whip the other end and that’s all you need. To use, pass the eye around something good and strong that is within a short distance from the loaded car. Examples, stantions welded to the deck, perforated toe rails, other sheeting cars even if the are in use. Pass the end through the eye. Take the other end to the loaded sheet forward of the car and tie it to the sheet using a rolling hitch. Snug it up, ease the sheet to get the load off the car. Adjust the car, move from one track to another, whatever you need to do. Sheet her home. You might have a bit of leech flutter, but absolutely no flogging! It’s only been a few weeks since I put this together. And have found many uses well beyond my original application. To store it while keeping it handy. I fold it in half twice then luggage tag it to a cabin top handrail. Just makes you wonder sometimes why did it take me 18 years to figure something so simple and cost effective to make and use.

Good way to save the sails. As you say, flogging is terrible for them.

We used to do something very like it back in the day when changing headsails while racing. Called it a “changing sheet”.

It seems to me that it is much more important how the lines are lead and how friction is minimized than whether the lines are lead aft. That means good hardware – blocks and sailtracks, and having only one 90 degree-bend at the mast-foot. A 30 or 45 degree redirection well executed doesn’t add that much friction. That also means avoiding single-line reefing and having a winch setup that is ergonomically sound.

TP 60ies that go around the world non-stop have everything led aft and it clearly works single-handed in very rough conditions. So do Class 40ies, though these “only” do 20 to 30 days non-stop. So do the (Volvo) Ocean race boats and the line-handling works like a charm (taking advantage of multi-person grinders, though).

Even so, I would go forward twice a day and check everything thoroughly, but I would do so during the day when I chose the time, not when I have to – possibly in the worst of times.

Hi John, Great article as always.

Curious about your take on the mainsheet routing on certain Amel Ketches where the traveler is forward of the dodger and the sheet is run aft over the dodger and enclosure to the mizen mast. (links/image below)

Also, are the effects of a traveler greatly affected when raised? Say, if the Boreal in your example had a flat dodger with traveler or like the arch mounted traveler seen on certain Hunters.

https://2.bp.blogspot.com/-BhQCF6mH238/W_8EN5MTOPI/AAAAAAABZqw/KSNjlEqzaQUVeBfzAbHCsLkTBMn65-lIwCLcBGAs/s1600/2017.10%2BGrenade%2BMartinique%2B%25289%2529.JPG

https://itboat.com/uploads/ae64/f5e25fdb8353.jpg

It seems a pity to have a nice safe traveler position like that and then lead the mainsheet in such a way as it can garrotte a crew member. If it were me designing the system I would go with a “German Mainsheet system” with the track where it is and the mainsheet double ended and lead back from blocks below the gooseneck to winches either side of the cockpit.

And yes, raising the mainsheet traveler closer to the boom enables windward sheeting with a shorter track.

Hey John, New to AAC, loving it so far, trying to soak up as much as I can. I am looking to re-rig my 1980 Ingrid 38 ketch, following the simple is best approach you teach here. We are preparing to sail her from San Diego to Japan (where we live) across the south pacific. Do you know any good riggers in the Southern California area? Boat is in San Diego.

Early this year I did a major refit of my Islander 36 with the excellent support of the Ventura Harbor Boatyard. Work completed included a rebuilt mast step, new cap/intermediate shroud chain plates, and new standing rigging. The boatyard recommended a local rigger, Kim Weir, and I was extremely pleased with his work. Without hesitation, I recommend the services of VHBY and Kim Weir.

Thanks for coming up on that.

Sorry, I have never sailed on the west coast, so don’t have any experience with riggers there. That said, Brian Toss’s old shop is still in business run by guys Brian taught, so that might be an option, although a ways from you: http://briontoss.com

Also see Steve’s comment.

No one has mentioned self-tacking jibs. Having owned two boats with them the thought of going back to winching every time you tack -particularly when singlehanded- fills me with horror. Huge genoas are, in any case, only a relic from ancient rating rules. Whether a jib boom ( particularly the internal boom as used on Freedom sloops) or jib traveller is used, short tacking becomes an effortless exercise. A small jib on a traveller can be trimmed more easily and efficiently than a Genoa. The mainsail is always the prime driver; the performance gain from oversized headsails is less than you think, and in these days of easily deployed offwind headsails is not a consideration off the wind.

I agree with most all you say, except I have never been a fan of jib booms, probably something to do with being naturally clumsy so I don’t need anything else to trip over on the foredeck!

Anyway, just loving sailing our J/109 with her big mainsail and blade jib.

On an otherwise good boat would you recommend moving the lines from the cockpit to the mast if you were going to have an e-wincher anyway, which would presumably overcome the extra friction while still giving the operator enough feel to know if something was going wrong?

Way too many variables to answer that: boat, usage, crew, how well the boat is set up with lines aft, and on it goes. That said, my 109 is lines aft and the wincher makes all the difference to practicality so I have no plans to change. That reminds me, I should do a tip on why.

• BOAT OF THE YEAR
• Newsletters
• Sailboat Reviews
• Boating Safety
• Sails and Rigging
• Maintenance
• Sailing Totem
• Sailor & Galley
• Living Aboard
• Destinations
• Gear & Electronics
• Charter Resources
• Ultimate Boating Giveaway

Sailboat Design Evolution

• By Dan Spurr
• Updated: June 10, 2020

You know the old saying, “The more things change, the more they stay the same”? As a judge for the 2020 Boat of the Year (BOTY) competition at this past fall’s US Sailboat Show in Annapolis, Maryland, I helped inspect and test-sail 22 brand-new current-model sailboats. And I came away thinking, Man, these aren’t the boats I grew up on. In the case of new boats, the saying is wrong: “Nothing stays the same.”

OK, sure, today’s boats still have masts and sails, and the monohulls still have keels. But comparing the Hinckley Bermuda 40, considered by many to be one of the most beautiful and seaworthy boats of the 1960s, ’70s and even ’80s, with, say, the Beneteau First Yacht 53, which debuted at the show, is pretty much apples and oranges.

To get a better sense of what has happened to yacht design, boatbuilding and equipment over the past three, four or even six decades, let’s take a closer look.

Design Dilemmas

At the risk of oversimplification, since the fiberglass era began in the late 1940s and ’50s, the design of midsize and full-size yachts has transitioned from the Cruising Club of America rules, which favored all-around boats (racers had to have comfortable interiors) with moderate beam and long overhangs, to a succession of racing rules such as the IOR, IMS and IRC. All of them dictated proportions, and each required a measurer to determine its rating.

As frustration grew with each (no handicap rule is perfect), alternatives arose, such as the Performance Handicap Racing Fleet, which essentially based one’s handicap on past performance of the same boats in the same fleet. Also, one-design racing became more popular, which spread beyond identical small boats to full-size yachts, popularized in part by builders such as J/Boats and Carroll Marine. The ethos there was: Who cares about intricate rating rules? Let’s just go out and sail fast and have fun!

And that might best sum up the design briefs for the monohulls in this year’s BOTY competition: good all-around performance with comfortable, even luxurious accommodations. Gone are interiors that noted naval architect Robert Perry called “the boy’s cabin in the woods,” deeply influenced by stodgy British designers of the past century and their now-old-fashioned (though ­sea-friendly, one should note) concepts of a proper yacht, drawn and spec’d by the same guy who designed the hull, deck and rig. Today, dedicated European interior designers are specially commissioned to inject modernity, home fashion colors and textures, amenities, and more light—even dubiously large port lights in the topsides.

Overhangs, bow and stern, have virtually disappeared. Why? It seems largely a matter of style. Plus, the bonus of increased usable space below, not to mention a longer waterline length for a given length overall, which translates to more speed. Former naval architect for C&C Yachts and Hunter Marine, Rob Mazza, recalls that 19th-century pilot cutters and fishing schooners operating in offshore conditions generally had plumb bows, so in a sense, bow forms have come full circle.

Today’s boats are carrying their wide beam farther aft. Gone are the days of the cod’s head and mackerel tail. Wide, flat canoe bodies are decidedly fast off the wind, and might even surf, but they pay a comfort penalty upwind.

These boats have lighter displacement/length (D/L) ratios, which means flatter bottoms and less stowage and space for tanks. The Beneteau 53 has a D/L of 118, compared with the ­aforementioned Bermuda 40 of 373. Among entries in this year’s BOTY, the heaviest D/L belonged to the Elan Impression 45.1, with a D/L of 195. Recall that when Perry’s extremely popular Valiant 40 was introduced in 1975, the cruising establishment howled that its D/L of 267 was unsuitable for offshore sailing. My, how times have changed!

Perhaps more important, one must ask: “Have the requirements for a good, safe bluewater cruiser actually changed? Or are the majority of today’s production sailboats really best-suited for coastal cruising?”

The ramifications of lighter displacement don’t end there; designers must consider two types of stability: form and ultimate. As weight is taken out of the boat, beam is increased to improve form stability. And with tanks and machinery sometimes raised, ­ballast might have to be added and/or lowered to improve ultimate stability.

What else to do? Make the boat bigger all around, which also improves stability and stowage. Certainly the average cruising boat today is longer than those of the earlier decades, both wood and fiberglass. And the necessarily shallower bilges mean pumps must be in good shape and of adequate size. That’s not as immediate an issue with a deep or full keel boat with internal ballast and a deep sump; for instance, I couldn’t reach the bottom of the sump in our 1977 Pearson 365.

And how do these wide, shallow, lighter boats handle under sail? Like a witch when cracked off the wind. We saw this trend beginning with shorthanded offshore racers like those of the BOC Challenge round-the-world race in the early 1980s. As CW executive editor Herb McCormick, who has some experience in these boats, says, “They’ll knock your teeth out upwind.” But route planning allows designers to minimize time upwind, and cruisers can too…if you have enough room and distance in front of you. Coastal sailors, on the other hand, will inevitably find even moderate displacement boats more comfortable as they punch into head seas trying to make port.

A wide beam carried aft permits a number of useful advantages: the possibility of a dinghy garage under the cockpit on larger boats; easy access to a swim platform and a launched dinghy; and twin helms, which are almost a necessity for good sightlines port and starboard. Of course, two of anything always costs twice as much as one.

Some multihulls now have reverse bows. This retro styling now looks space-age. Very cool. But not everyone is sold on them. Canadian designer Laurie McGowan wrote in a Professional BoatBuilder opinion piece, “I saw through the fog of faddishness and realized that reverse bows are designed to fail—that is, to cause vessels to plunge when lift is required.” Mazza ­concurs: “Modern multihulls often have ­reverse stems with negative reserve buoyancy, and those are boats that really can’t afford to bury their bows.”

McGowan also cites another designer critiquing reverse bows for being noticeably wet and requiring alternative ground-­tackle arrangements. The latter also is problematic on plumb bows, strongly suggesting a platform or sprit to keep the anchor away from the stem.

Rigging Redux

If there was a boat in Annapolis with double lower shrouds, single uppers, and spreaders ­perpendicular to the boat’s centerline, I must have missed it. I believe every boat we sailed had swept-back spreaders and single lowers. An early criticism of extreme swept-back spreaders, as seen on some B&R rigs installed on Hunter sailboats, was that they prevented fully winging out the mainsail. The counter argument was that so many average sailors never go dead downwind in any case, and broad reaching might get them to their destinations faster anyway—and with their lunch sandwiches still in their stomachs.

That issue aside, the current rigging configuration may allow for better mainsail shape. But as Mazza points out, it’s not necessarily simple: “By sweeping the spreaders, the ‘transverse’ rigging starts to add fore-and-aft support to the midsection of the mast as well, reducing the need for the forward lowers. However, spreader sweep really does complicate rig tuning, especially if you are using the fixed backstay to induce headstay tension. Swept spreaders do make it easier to sheet non-overlapping headsails, and do better support the top of the forestay on fractional rigs.”

Certainly, the days of 150 ­percent genoas are over, replaced by 100 percent jibs that fit ­perfectly in the foretriangle, often as a self-tacker.

Another notable piece of rigging the judges found common was some form of lazy jacks or mainsail containment, from traditional, multiple lines secured at the mast and boom; to the Dutchman system with monofilament run through cringles sewn into the sail like a window blind; to sailmaker solutions like the Doyle StackPak. This is good news for all sailors, especially those who sail shorthanded on larger boats.

Construction Codas

Improvements in tooling—that is, the making of molds—are easily evident in today’s boats, particularly with deck details, and in fairness. That’s because many of today’s tools are designed with computer software that is extraordinarily accurate, and that accuracy is transferred flawlessly to big five-axis routers that sculpt from giant blocks of foam the desired shape to within thousandths of an inch. Gone are the days of lofting lines on a plywood floor, taken from a table of offsets, and then building a male plug with wood planks and frames. I once owned a 1960s-era sailboat, built by a reputable company, where the centerline of the cockpit was 7 degrees off the centerline of the deck—and they were one piece!

Additive processes, such as 3D printing, are quickly complementing subtractive processes like the milling described above. Already, a company in California has made a multipart mold for a 34-foot sailboat. Advantages include less waste materials.

Job training also has had an impact on the quality of fiberglass boats. There are now ­numerous schools across the country offering basic-skills training in composites that include spraying molds with gelcoat, lamination, and an introduction to vacuum bagging and infusion.

The patent on SCRIMP—­perhaps the first widely employed infusion process—has long ago expired, but many builders have adopted it or a similar process whereby layers of fiberglass are placed in the mold dry along with a network of tubes that will carry resin under vacuum pressure to each area of the hull. After careful placement, the entire mold is covered with a bag, a vacuum is drawn by a pump, and lines to the pot of resin are opened. If done correctly, the result is a more uniform fiberglass part with a more controlled glass-to-resin ratio than is achievable with hand lay-up. And as a huge bonus, there are no volatile organic compounds released into the workplace, and no need for expensive exhaust fans and ductwork. OSHA likes that, and so do the workers.

However, sloppy processes and glasswork can still be found on some new boats. Surveyor Jonathan Klopman—who is based in Marblehead, Massachusetts, but has inspected dozens, if not hundreds, of boats damaged by hurricanes in the Caribbean—tells me that he is appalled by some of the shoddy work he sees, such as balsa cores not vacuum-bagged to the fiberglass skins, resulting in delamination. But overall, I ­believe workmanship has improved, which is evident when you look behind backrests, inside lockers and into bilges, where the tidiness of glasswork (or lack thereof) is often exposed. Mechanical and electrical systems also have improved, in part due to the promulgation of standards by the American Boat & Yacht Council, and informal enforcement by insurance companies and surveyors.

We all know stainless steel isn’t entirely stainless, and that penetrations in the deck are potentially troublesome; allowing moisture to enter a core material, such as end-grain balsa, can have serious consequences. The core and fiberglass skins must be properly bonded and the kerfs not filled with resin. Beginning in the mid-1990s, some builders such as TPI, which built the early Lagoon cruising catamarans, began using structural adhesives, like Plexus, to bond the hull/deck joint rather than using dozens of metal fasteners. These methacrylate resins are now commonly used for this application and others. Klopman says it basically should be considered a permanent bond, that the two parts, in effect, become one. If you think a through-bolted hull/deck joint makes more sense because one could theoretically separate them for repairs, consider how likely that would ever be: not highly.

Fit-and-Finish

Wide transoms spawned an unexpected bonus; besides the possibility of a dinghy “garage” under the cockpit on larger boats, swim platforms are also possible. In more than one BOTY yacht, the aft end of the cockpit rotated down hydraulically to form the swim platform—pretty slick.

Teak decks are still around, despite their spurning for many years by owners who didn’t want the upkeep. In the 1960s and ’70s, they were considered a sign of a classy boat but fell from favor for a variety of reasons: maintenance, weight and threat of damaging the deck core (the bung sealant wears out and water travels down the fastener through the top fiberglass skin into the core). Specialty companies that supply builders, like Teakdecking Systems in Florida, use epoxy resin to bond their product to decks rather than metal fasteners. And the BOTY judges saw several synthetic faux-teak products that are difficult to distinguish from real teak—the Esthec installed on the Bavaria C50 being one example.

LPG tanks no longer have to be strapped to a stanchion or mounted in a deck box because decks now often incorporate molded lockers specifically designed for one or two tanks of a given size. To meet ABYC standards, they drain overboard. In tandem with these lockers, some boats also have placements or mounts for barbecues that are located out of the wind, obviating the common and exposed stern-rail mount.

Low-voltage LED lights are replacing incandescent bulbs in nearly all applications; ­improvements in technology have increased brightness (lumens), so some even meet requirements for the range of navigation lights. Advances in battery technology translate to longer life, and depending on type, faster charging. And networked digital switching systems for DC-power ­distribution also are becoming more common.

Last, I was surprised at how many expensive yachts exhibited at Annapolis had nearly the least-expensive toilets one can buy. Considering the grief caused by small joker valves and poorly sealed hand pumps, one would think builders might install ­systems that incorporate higher-quality parts or vacuum ­flushing, and eliminate the minimal hosing that famously permeate odors.

Dan Spurr is an author, editor and cruising sailor who has served on the staffs of Cruising World, Practical Sailor and Professional Boatbuilder. His many books include Heart of Glass , a history of fiberglass boatbuilding and boatbuilders .

Other Design Observations

Here are a few other (surprising) items gleaned from several days of walking the docks and sailing the latest models:

• Multihulls have gained acceptance, though many ­production models are aimed more at the charter trade than private ownership for solitary cruising. You’d have to have been into boats back in the ’60s and ’70s to remember how skeptical and alarmist the sailing establishment was of two- and three-hull boats: “They’ll capsize and then you’ll drown.” That myth has been roundly debunked. Back then, the only fiberglass-­production multihulls were from Europe, many from Prout, which exported a few to the US. There are still plenty of European builders, particularly from France, but South Africa is now a major player in the catamaran market.
• The French builders now own the world market, which of course includes the US. Other than Catalina, few US ­builders are making a similar impact. In terms of volume, Groupe Beneteau is the largest builder in the world, and they’ve expanded way beyond sailboats into powerboats, runabouts and trawlers.
• Prices seem to have outpaced inflation, perhaps because, like with automobiles, where everyone wants air conditioning, electric windows and automatic transmissions, today’s boats incorporate as standard equipment items that used to be optional. Think hot- and cold-pressure water, pedestal-wheel steering, and full suites of sailing instruments and autopilots.
• More: design , print may 2020 , Sailboats
• More Sailboats

Pre-Owned: 1988 Hylas 47

Catalina Introduces the 6 Series

Sailboat Preview: Elan GT6 Explorer

For Sale: 1984 Camper & Nicholsons 58

Galápagos: A Paradise Worth the Paperwork

Around Alone

Grease the Wheels of Your Boat: A Guide to Proper Lubrication

A Bowsprit Reborn: A DIY Renovation Story

• Digital Edition
• Customer Service
• Privacy Policy
• Terms of Use
• Email Newsletters
• Cruising World
• Sailing World
• Salt Water Sportsman
• Sport Fishing
• Wakeboarding

IT’S NEVER BEEN EASIER TO BUILD THE BOAT YOU’VE ALWAYS WANTED

Email steve to talk boat design, why choose tboat design.

You can either use a STOCK DESIGN or a CUSTOM DESIGN to build your boat.

Download my free boatbuilding process

OUR BOAT DESIGN PROCESS

• We talk together to help define the boat you want and decide if you need a custom or ready-made design, and who will build it. • We scope out your project, customising a stock design or start from scratch on a new custom design • Plans are delivered, ready to be built and launched, help is only an email away

“I have worked with Steve to design and build my own custom T9 canting racing yacht in Australia. I can highly recommend Steve’s design and build processes to make the experience easier. Check out my experience building the boat here” Johnno Whitfield

Open Johnno’s full experience

What can you expect from a TBOAT design

• A highly functional, high performance design • Complete performance analysis and engineered design • weight conscious, using modern materials • Plans and directions that are simple to follow • Full sized templates • Detailed materials and parts list • Drawings • Detailed build methodology • Support during the building process

Click on thumb to open YouTube video

Open steve’s video

SIGN UP FOR TBOAT NEWSLETTER

Hello @ tboat.com.

Hauraki Gulf Auckland, New Zealand

Country USA Australia New Zealand England France Croatia Czechia (Czech Republic) Germany Italy Spain Saudi Arabia China Thailand Vietnam Hong Kong Japan South Africa Afghanistan Albania Algeria Andorra Angola Antigua and Barbuda Argentina Armenia Austria Azerbaijan Bahamas Bahrain Bangladesh Barbados Belarus Belgium Belize Benin Bhutan Bolivia Bosnia and Herzegovina Botswana Brazil Brunei Bulgaria Burkina Faso Burundi Côte d'Ivoire Cabo Verde Cambodia Cameroon Canada Central African Republic Chad Chile Colombia Comoros Congo (Congo-Brazzaville) Costa Rica Cuba Cyprus Democratic Republic of the Congo Denmark Djibouti Dominica Dominican Republic Ecuador Egypt El Salvador Equatorial Guinea Eritrea Estonia Eswatini (fmr. "Swaziland") Ethiopia Fiji Finland Gabon Gambia Georgia Ghana Greece Grenada Guatemala Guinea Guinea-Bissau Guyana Haiti Holy See Honduras Hungary Iceland India Indonesia Iran Iraq Ireland Israel Jamaica Jordan Kazakhstan Kenya Kiribati Kuwait Kyrgyzstan Laos Latvia Lebanon Lesotho Liberia Libya Liechtenstein Lithuania Luxembourg Madagascar Malawi Malaysia Maldives Mali Malta Marshall Islands Mauritania Mauritius Mexico Micronesia Moldova Monaco Mongolia Montenegro Morocco Mozambique Myanmar (formerly Burma) Namibia Nauru Nepal Netherlands Nicaragua Niger Nigeria North Korea North Macedonia (formerly Macedonia) Norway Oman Pakistan Palau Palestine State Panama Papua New Guinea Paraguay Peru Philippines Poland Portugal Qatar Romania Russia Rwanda Saint Kitts and Nevis Saint Lucia Saint Vincent and the Grenadines Samoa San Marino Sao Tome and Principe Senegal Serbia Seychelles Sierra Leone Singapore Slovakia Slovenia Solomon Islands Somalia South Korea South Sudan Sri Lanka Sudan Suriname Sweden Switzerland Syria Tajikistan Tanzania Timor-Leste Togo Tonga Trinidad and Tobago Tunisia Turkey Turkmenistan Tuvalu Uganda Ukraine United Arab Emirates United Kingdom Uruguay Uzbekistan Vanuatu Venezuela Yemen Zambia Zimbabwe

Please fill out the form and we will send you the "Sail To Success" link

Email Address:

Recieve our newsletter

We noticed you're visiting from United Kingdom (UK). We've updated our prices to Pound sterling for your shopping convenience. Use New Zealand dollar instead. Dismiss

Automated page speed optimizations for fast site performance

The global authority in superyachting

• NEWSLETTERS
• Yachts Home
• The Superyacht Directory
• Yacht Reports
• Brokerage News
• The largest yachts in the world
• The Register
• Yacht Advice

Yacht Design

• 12m to 24m yachts
• Monaco Yacht Show
• Builder Directory
• Designer Directory
• Interior Design Directory
• Naval Architect Directory
• Yachts for sale home
• Motor yachts
• Sailing yachts
• Explorer yachts
• Classic yachts
• Sale Broker Directory
• Charter Home
• Yachts for Charter
• Charter Destinations
• Charter Broker Directory
• Destinations Home
• Mediterranean
• South Pacific
• Rest of the World
• Boat Life Home
• Owners' Experiences
• Conservation and Philanthropy
• Interiors Suppliers
• Owners' Club
• Captains' Club
• BOAT Showcase
• Boat Presents
• Events Home
• World Superyacht Awards
• Superyacht Design Festival
• Design and Innovation Awards
• Young Designer of the Year Award
• Artistry and Craft Awards
• Explorer Yachts Summit
• Ocean Talks
• The Ocean Awards
• BOAT Connect
• Between the bays
• Golf Invitational
• BOATPro Home
• Superyacht Insight
• Global Order Book
• Premium Content
• Product Features
• Testimonials
• Pricing Plan
• Tenders & Equipment

Keep up-to-date with the latest design trends with our design news , get the inside story on how the most iconic luxury superyachts were designed and find out more about the world’s best superyacht designers

In conversation with...

More on superyacht design & interiors, iconic yachts, charter a masterpiece, latest yacht news, from our partners, sponsored listings.

• New Sailboats
• Sailboats 21-30ft
• Sailboats 31-35ft
• Sailboats 36-40ft
• Sailboats Over 40ft
• Sailboats Under 21feet
• used_sailboats
• Apps and Computer Programs
• Communications
• Fishfinders
• Handheld Electronics
• Plotters MFDS Rradar
• Wind, Speed & Depth Instruments
• Anchoring Mooring
• Running Rigging
• Sails Canvas
• Standing Rigging
• Diesel Engines
• Off Grid Energy
• Cleaning Waxing
• DIY Projects
• Repair, Tools & Materials
• Spare Parts
• Tools & Gadgets
• Cabin Comfort
• Ventilation
• Footwear Apparel
• Foul Weather Gear
• Mailport & PS Advisor
• Inside Practical Sailor Blog
• Activate My Web Access
• Reset Password
• Customer Service

• Free Newsletter

Blue Jacket 40 Used Boat Review

Catalina 270 vs. The Beneteau First 265 Used Boat Match-Up

Ericson 41 Used Boat Review

Mason 33 Used Boat Review

How to Create a Bullet-Proof VHF/SSB Backup

Tips From A First “Sail” on the ICW

Tillerpilot Tips and Safety Cautions

Best Crimpers and Strippers for Fixing Marine Electrical Connectors

Polyester vs. Nylon Rode

Getting the Most Out of Older Sails

How (Not) to Tie Your Boat to a Dock

Stopping Mainsheet Twist

Fuel Lift Pump: Easy DIY Diesel Fuel System Diagnostic and Repair

Ensuring Safe Shorepower

Sinking? Check Your Stuffing Box

What Do You Do With Old Fiberglass Boats?

Boat Repairs for the Technically Illiterate

Boat Maintenance for the Technically Illiterate

Whats the Best Way to Restore Clear Plastic Windows?

Stopping Holding-tank Odors

Giving Bugs the Big Goodbye

Galley Gadgets for the Cruising Sailor

The Rain Catcher’s Guide

Sailing Gear for Kids

What’s the Best Sunscreen?

UV Clothing: Is It Worth the Hype?

Preparing Yourself for Solo Sailing

R. Tucker Thompson Tall Ship Youth Voyage

On Watch: This 60-Year-Old Hinckley Pilot 35 is Also a Working…

On Watch: America’s Cup

On Watch: All Eyes on Europe Sail Racing

Dear Readers

• Sailboat Reviews
• Sails, Rigging & Deck Gear

A Practical Look at Sailboat Cockpit Design

Ps outlines what to look for when searching for a comfortable, functional cockpit..

Cockpit ergonomics involve more than a concern about coaming angles and comfortable seating. These are just two items on a long list of attributes that define the space where sailors spend most of their waking time.

At boat shows, the crowd can be divided into those that poke around on deck and those who head directly below. Brokers know the difference between racing sailors and cruisers and which end of the companionway ladder will seal the deal. Racers want performance and scrutinize the on-deck design features that make it all happen, while cruisers look below for the amenities of a house afloat. This stereotype may be too rigid, but from what we’ve seen at recent boat shows, cruisers need to take a closer look at the cockpit and get a feel for how a sailboat will handle underway, as well as serve as a home away from home.

There’s much more at stake than comfort for the crew. Cockpit design and layout drives many boat-handling tasks, ranging from steering and sail trimming to what goes on when its time to reef. Angles of view can even affect watchkeeping.

For example, a high center cockpit and a large overlapping genoa create a 90-degree-plus no see zone, and thats a big deal when it comes to collision avoidance. A large catamaran with a tall bridge-deck cabin can add an even larger no see zone, especially when running on autopilot with no one perched on the elevated helm seat.

In short, many cockpits are optimized for at-anchor enjoyment instead of underway usability. So part of the boat-shopping process should include careful scrutiny of how essential sailing and boat-handling tasks will be accomplished. For starters, note how much contortion it takes to really crank each winch, determine whether or not the line leads favor easy reefing, and check to see how well the cockpit shape contributes to keeping the crew from being washed overboard. These are essential attributes, and for some, they are more vital than galley counter material and the fabric that covers the cushions below.

Grand Prix racers have long favored wide open, low sided, no-transom cockpits that are more of an open deck than a protective trench. In heavy weather, these nothing-to-cling-to cockpits can become perilous. In 1997, during the Hong Kong to Osaka, Japan Race, Americas Cup trials veteran Makoto Namba was at the helm of Escape One when a 20-foot breaking sea washed him out the open transom of the 45-foot racer. In 2006, Dutch Volvo Ocean racer Hans Horrevoets was swept from the deck of ABN AMRO TWO and lost at sea. Closer to home, pro sailor Dan Cianci was tossed over the lifelines of the 50-foot ocean racer Snow Lion. The accident occurred at night, in heavy weather just off the Delaware River mouth. In each case, the cockpit design favored sail trim and line handling over heavy-weather safety considerations. Many ocean racers mitigate such design tradeoffs with careful use of harnesses, tethers, jack lines, and hard points for tether attachment.

Just the opposite design trend can be found in the deep cockpit and conventional closed transom of sailboats such as Ted Hoods 25-year-old design, American Promise. Dodge Morgan sailed the heavy-displacement 60-footer solo around the world. The big, double-head rigged sloop provided a great deal of crew protection and seakeeping ability during Morgans voyage. And for years after he donated the boat to the U.S. Naval Academy, midshipmen also learned to appreciate the cockpit layout-particularly during bad weather offshore.

PS Technical Editor Ralph Naranjo sailed that boat in a gale-strewn trans-Atlantic with an able crew and encountered a nasty 979-millibar low at about 45 degrees North latitude. According to the log, AP was reaching eastward at 9 knots under storm trysail and storm jib with green water routinely sweeping the deck. Seas had silenced the mini-M satphone by regularly immersing the dome shaped antenna in wave faces, eventually flooding the internal circuitry.

It was a rough passage, and little things taken for granted in smoother seas showed their true value. Features like the deep cockpit well, the heavy-duty, water-tight companionway doors, and the massive cockpit drains all proved their worth.

The flip side of the coin is that really bad weather encounters are a rare occurrence for most sailors. More often, 0- to 20-knot sailing conditions prevail. And our coastline is dotted with safe havens in which to hide from the elements. So one of the big challenges facing every designer and naval architect drawing lines for their next new boat is the question of exposure. Will owners use the boat as a dockside second home and be underway only in fair weather, or will they take the cruiser label to heart and leave land well astern? A close look at cockpit layouts will give you some indication of the boats intended use.

We prefer to evaluate cockpit ergonomics from both static and dynamic points of view. On some boats, these underway and at anchor evaluations lead to disparate conclusions. A cockpit that works well underway may be confining in port, or another vessel with a patio-size stern may be altogether dysfunctional at sea. It’s all an issue of trying to do two different jobs with one fixed set of dimensions and appendages. Buyers need to know what attributes they will make best use of.

For monohulls, coping with heel is the first big challenge, and wide-open space, whether its in the cockpit or main saloon, can be a tough challenge. The universal solution to carrying wide beam aft on cruising boats seems to be the ubiquitous cockpit table. It can be a handy centerline support, but it’s a tough addition to a seafaring cockpit in the minds of many traditional sailors. That said, production boatbuilders have gotten much better at making these centerline, folding-leaf tables sturdy enough for sea duty and effective as a handhold.

Industry Trends

Over the last 50 years, mainstream production sailboat design has moved noticeably away from the racer/cruiser defined by Pearson, Tartan, C&C, Cal, Columbia, Ranger, Islander, Ericson, and others. The new boats are roomier with less emphasis on performance under sail. Racers now have their own genre of sailboat, and they are faster, better handling, and more capable than their predecessors. But whats most surprising is that many mainstream cruisers are anything but optimized for long-distance passages and long-term living aboard.

These boats feature convenience, style, and comfort, and the actual design objective in many cases is more focused on weekend cruising and an annual two-week summer harbor-hopping cruise. Easy sail-setting and large boat interiors in shorter waterline lengths prevail, and such trends influence the shape and layout of the cockpit. When it comes to ergonomics, the split between cruisers and racers is more apparent than ever, but theres also some real differentiation within the ranks of cruisers themselves.

In Practical Sailors recent scrutiny of cockpit designs at local boat shows, weve noted four emerging sailboat stereotypes. These include daysailers that feature few, if any, accommodations; racing boats brimming with performance-enhancing hardware; and ocean-going cruisers capable of extended passagemaking. The fourth grouping-larger than all the other three combined-are also labeled cruisers, but with less draft, less stability, and less versatile sail plans, they are more like an SUV designed more for the highway than off-roading in the backcountry.

Sizing Up a Cockpit

The takeaway lesson for us was the importance of making sure that the cockpit of the boat you are about to buy is in keeping with the mission of the rest of the boat. If you are a serious club racer, the centerline table wont be a crew favorite. Those making a double-handed passage on a 40-footer will see a tight, narrow cockpit differently than when eight sail the same boat. So with complete belief in the old adage, different strokes for different folks, heres what we looked for when evaluating cockpit design. It can be used as a helpful buyers guide when you’re surveying your next boat.

Working the winches: All too often, winch location is an afterthought, and fine hardware is stuck on side coamings shaped more as a roof for the aft cabin than as a key component of sail trim. We always like to check sheet leads angles that lead lines to a particular winch and then mimic what cranking with a two-handed winch handle would be like. Look for 360-degree clearance with no knuckle-busting stanchions in the way. Be sure that the winch grinding works on either tack. Genoa sheeting may always put you on the leeward side of the cockpit, but runners and spinnaker guys will usually be worked on a windward winch.

Sheets and halyards: One of testers major complaints was builders habit of running seldom-used halyard lines attached to roller-furling headsails and in-mast furling mainsails all the way aft to the cockpit. Doing so left lengthy line tails cluttering up the area under the dodger where reefing lines, the boom vang, and in some cases, the main sheet all arrived like too many trains in a station.

Theres no perfect mainsheet arrangement, but some are better than others, and the one you choose has a lot to do with how much attention you pay to the nuance of sail trim. The current vogue among serious racers involves 2-to-1 end-boom sheeting: an in-boom lead of the double-ended sheet returns aft via turning blocks near the mast and runs to winches on both sides of the boat (often referred to as Admirals Cup, or German mainsheet). Fast, no-load hand trimming is the upside, but in any breeze, theres good reason to quickly get the sheet on a winch drum. The sheet tail is shorter because of the low ratio (2-to-1) lead. One nuisance is that the sheet can end up bunched up on one side or the other.

Many cruisers prefer higher ratio, multi-part tackles for mainsheeting and may lead each end to a Harken-type adjustment system rather than using a winch. When fast tacking action is not in the cards, this is a user-friendly system.

Some cruisers incorporate mid-boom sheeting because it moves the tackle out of the cockpit than rather then because of how effectively it allows the mainsail to be trimmed. The shortened lever arm means the sheet needs a winch sooner than later. There is also more of a leech-flattening, vang-like effect to this type of sheeting, not the best feature for light-air efficiency.

The trend toward travelers roosting on over-cockpit arches, a longtime standard in Hunter Yachts and a recent adoption in some Beneteau lines, helps protect the crew from accidental jibe injuries and allows dodgers and biminis to flourish, but windows in these covers are essential, if a crew is to see whats happening whey they are pulling the strings.

Anticipate the angles: Look at how things will change as heel increases and note where vulnerability lies. We recently ran into a crew who had lost an engine due to the shape of the cockpit. During the design phase, the location for an engine instrument recess was placed within easy reach of the person at the helm. In an upright trim-and even at 30 degrees of heel-all was well, but in a knock down when the cockpit began to flood, the engine instruments ended up in a low spot, and despite their sealed all-weather design, submerging them in saltwater had not been part of the engine manufacturers gameplan. The ensuing corrosion took out the panel and the alarm system, and a novice crew failed to notice the changes in sound and smell as a raw-water blockage in the cooling system went critical.

Those headed offshore need to pay special heed to the companionway and have a feel for what angle of heel sends water down an open hatch. Whats a surprise to many is that the first part of the hatch to reach the water may be the top rather than the lower portion of the companionway. Sticking in a washboard or two will help keep a breaking wave from sloshing below, but it may be of little use in a deep knockdown.

Getting in and out: One of the most important safety features of a good boat is the transitional path that leads a crew from the cockpit to the deck. Good engineering focuses on step heights, deck camber, handholds, and the quality of the nonskid surface. This transition in and out of the cockpit is one of the most repeated movements on the vessel. If a dodger, bimini, or Florida room compromises access, they become a hazard. Small, molded steps are of little help in a seaway.

There is no ideal cockpit that meets everyones preferences, and plenty of bad ideas still persist. No matter what your aims are as a sailor, some things deserve to take precedence. Ample space for entertaining friends for sundowners dockside is nice, but comfort underway, including ergonomic seats for sitting or napping, and secure places to steer and stand watch when the boat is heeled should be a higher priority.

Likewise, sight lines and sensible sheet arrangements should come before drink-holders. Next time you prowl the boat show, spend some time exploring the cockpit and comparing features. It is the hub of the boat.

Rating cockpit attributes is a worthwhile endeavor for a serious boat shopper. Start by rating component parts. It will allow you to more effectively compare and contrast one boat with another, according to your specific sailing plans and needs.

For example: Above, we have focused on seven key cockpit attributes and rated five new boats accordingly. Below is a brief explanation of each of the criteria selected. The result of the data table is not a winner-take-all report card. It’s a means of determining what has been emphasized in a specific cockpit design on a wide variety of very different vessels.

Rating for this attribute reflects both the location of a winch and the way in which crew members must bend, lean, or contort themselves while sheeting. We considered how efficiently a manual winch could be cranked and whether or not an electric winch could be safely operated while retaining a clear view of the sail being sheeted or hoisted.

This was not a look at the vessel’s steering hardware, rudder design, or feel of the tiller. It was more focused on helm location and how the person steering the boat could carry on the process comfortably for lengthy periods of time.

We consider the ability to quickly and efficiently reduce and add sail area to be a primary aspect of seamanship. Cockpit layouts teamed up with efficient well-chosen hardware can make or break this facet of cockpit ergonomics. Awkward winch placement, too many lines clustered together around a big bank of rope clutches, and attempting to place sheets, halyards, and reefing lines all in the helmsman’s lap with only one or two undersized winches usually lead to lower ratings.

Collision avoidance requires seeing what’s about to cause trouble well ahead of time, and anything shy of a 360-degree angle of view detracts from the process. We were concerned about view angles and obstructions ranging from dodgers, to deck-sweeping headsails, cabinhouse bulkheads, and other design features that limit the helmsperson’s field of vision. Aboard many multihulls, there’s a growing trend toward providing one perch that offers an all-around view. But when the vessel is operating on autopilot and no one is in the elevated helm seat, watchkeeping efforts are hampered.

When floating on an even keel, it’s easy to get in and out of most cockpits. However, a modest heel of 15 degrees can turn wide-open cockpits with awkward coamings and narrow sidedecks into a hazard. Getting around on a vessel in a seaway requires good nonskid, an abundance of ready handholds, and an unobstructed pathway in and out of the cockpit. Seats need to be usable underway, and the dodger, companionway, and bimini must work in concert.

Short Handing

Because most cruisers sail short-handed, we are always on the look out for features that make watchkeeping more user friendly. These include line leads and winch layouts that allow headsail trimming from the helm and may even offer the chance to tuck or shake a reef from the confine of the cockpit. Crew alone on deck also benefit from deeper-welled open space. Giving the short-handed crew protection from seeping seas and offering well-placed hardware goes a long way to ensure safe, efficient passagemaking.

Entertaining

At anchor and in port, the cockpit changes from an operations center to a backyard patio. Gone is the need for seakeeping attributes, and what counts is how well the area at the aft or center portion of the boat stacks up as a place for stationary fun. Tables that can serve dinner for six or drinks for 10 get high marks. Transoms that fold down, offering access to the sea, are also a current rage. It’s no surprise however, that many of the attributes that drive high scores for entertaining earn a lower grade at sea—the reason many designers and builders have spent time developing fold-up swim platforms and wellreinforced drop-leaf tables ready for sea duty.

VALUE GUIDE: Comparing Cockpit Design

RELATED ARTICLES MORE FROM AUTHOR

Leave a reply cancel reply.

Log in to leave a comment

Latest Videos

Cabo Rico 34 Boat Review

Super Shallow Draft Sailboat: The Leeboard Sharpie

Hans Christian 41T – Boat Review

Seven dead after superyacht sinks off Sicily. Was the crew at...

Latest sailboat review.

• Privacy Policy
• Do Not Sell My Personal Information
• Online Account Activation
• Privacy Manager

• OC Wally Cento
• 84 Mini Maxi
• IMOCA Open 60
• Consultancy Services
• 30m Blue Water Cruiser
• 25m Explorer Yacht
• 24m Fast Cruising Catamaran
• 23m Performance Cruiser
• 20m Explorer Yacht
• 20m High Performance Cruiser
• 18m Blue Water Cruiser
• 15m Performance Cruiser
• 15m Explorer Yacht
• 12m Explorer Yacht
• Multihull Design
• 18m Explorer Yacht
• 40m Blue Water Cruiser
• 40m Cruiser Racer
• 33m Performance Cruiser
• 30m Wally Cento
• 24m ORCsy Racer Cruiser
• 24m Day Sailer
• Carbon Component Design
• Yacht Performance Development
• CFD and Model Testing
• Twin Rudder Steering Systems
• Custom Deck Hardware
• Modifications and Refit
• VPP Routing and Sail Analysis
• Classic Yacht Refit & Optimisation
• Naval Architecture
• Engineering
• Rudder Design
• Brokerage Services
• 'Seahorse Magazine' #192
• 'Divoc' #190
• Lucent #180
• Influence #171
• 'Eora' #169
• 'The Three Brothers' #168
• 'Edenred' #165
• 'BHB3' #163
• 'Teata' #148
• 'Kite' #144
• ‘Sensei’ #131
• 'Gryphon' #106
• 'Horizon' #104
• 'Sabre II' #93
• 'Letto Di Pletto' #47
• 'Mowgli' #41
• 'Graybeard' #39
• 23.8m Ultime Trimaran
• 20.7m Orma Trimaran
• 18.28m Orma Trimaran
• 16.75m Cruising Catamaran
• 16.1m Cruising Catamaran
• 12.8m Crowther Shockwave Catamaran
• 9.1m Seacart 30 Trimaran
• 26.3m Aluminium Sloop
• 21.0m Steel Schooner
• 21.0m Aluminium Cruising Ketch
• 20.0m Aluminium Explorer Yacht
• 20.0m Luca Brenta Racer Cruiser
• 19.6m Aluminium Bluewater Cruiser
• 19.2m Aluminium Lifting Keel Sloop
• 18.8m Custom Steel Sloop
• 16.0m Sly Cruiser Racer
• 14.5m Aluminium Cruising yacht
• 13.87m Wooden Motor Sailer
• 25.25m Reichel Pugh Maxi
• 18.28m IMOCA 60 Nexans WeWise
• 18.28m IMOCA 60 'Canada Ocean Racing'
• 18.28m IMOCA 60 Gentoo
• 18.28m IMOCA 60 One Planet
• 15.85m TP52 Georgia
• 15.84m TP52 Racing Yacht 'Alizee'
• 15.25m Pegasus Open 50
• 12.8m Fast 40
• 10.89m Figaro 3
• 10.11m Sun Fast 3300
• 19.2m Lifting Keel Sloop
• 14.5m Aluminium Cruising Yacht

MIKE WALLER 

Yacht design.

WE SPECIALIZE IN BOAT PLANS FOR AMATEUR BUILDERS

We provide stock boat plans for both monohull and multihull sailing vessels, including sailing skiffs and sharpies. Our designs mainly feature timber construction, in plywood or cedar strip plank composite construction, using the W.E.S.T. system (wood epoxy saturation technique). Our designs are intended mainly as cruising boats, although several have done well in racing. All designs are suitable for amateur boat builders.

 MONOHULLS

 multihulls  , photos from our builders.

Photo galleries are provided on each design page where available

Please use a modern browser to view this website. Some elements might not work as expected when using Internet Explorer.

• Landing Page
• Luxury Yacht Vacation Types
• Corporate Yacht Charter
• Tailor Made Vacations
• Luxury Exploration Vacations
• View All 3704
• Motor Yachts
• Sailing Yachts
• Classic Yachts
• Catamaran Yachts
• Filter By Destination
• More Filters
• Latest Reviews
• Charter Special Offers
• Destination Guides
• Inspiration & Features
• Mediterranean Charter Yachts
• France Charter Yachts
• Italy Charter Yachts
• Croatia Charter Yachts
• Greece Charter Yachts
• Turkey Charter Yachts
• Bahamas Charter Yachts
• Caribbean Charter Yachts
• Australia Charter Yachts
• Thailand Charter Yachts
• Dubai Charter Yachts
• Destination News
• New To Fleet
• Charter Fleet Updates
• Special Offers
• Industry News
• Yacht Shows
• Corporate Charter
• Finding a Yacht Broker
• Charter Preferences
• Questions & Answers
• Add my yacht

SALUTE Yacht Layout & GA Plans

30.02m  /  98'6   benetti   2008.

• Previous Yacht
• Amenities & Toys
• Rates & Regions
• + Shortlist

Use two fingers to move the deck plan

Use ctrl + scroll to zoom the deck plan

Use ⌘ + scroll to zoom the deck plan

Zoomable Deck Plans Instructions To view the yacht General Arrangement / Deck Plans in more detail use the Zoom Tools + / - buttons to 'zoom in' or ' zoom out'. To navigate around hold down you mouse and drag to look around or for touch use two fingers to pinch and drag. To zoom with the mousewheel hold CTRL/⌘ and use the mouse wheel or use two fingers to scroll on an Apple touch pad.

SIMILAR YACHTS FOR CHARTER

28m | Tecnomar

from $44,000 p/week

Current $ea

29m | Princess

from $55,000 p/week

28m | Sunseeker

POA ♦︎

31m | Custom Line

from $69,000 p/week ♦︎

30m | Horizon

from $60,000 p/week

For Your Eyes Only

31m | Astondoa

from $70,500 p/week

31m | Azimut

from $65,000 p/week

31m | Gulf Craft

from $52,000 p/week ♦︎

Inspiration B

30m | Custom Line

from $59,000 p/week ♦︎

29m | Dominator

from $55,000 p/week ♦︎

30m | Bilgin Yachts

from $58,700 p/week

NOTE to U.S. Customs & Border Protection

Charter Salute

To charter this luxury yacht contact your charter broker or

SIMILAR LUXURY CHARTER YACHTS

Here are a selection of yachts which are similar to the current charter yacht. To view all similar luxury charter yachts click on the button below.

As Featured In

The YachtCharterFleet Difference

YachtCharterFleet makes it easy to find the yacht charter vacation that is right for you. We combine thousands of yacht listings with local destination information, sample itineraries and experiences to deliver the world's most comprehensive yacht charter website.

San Francisco

• Like us on Facebook
• Follow us on Twitter
• Follow us on Instagram
• Find us on LinkedIn
• Add My Yacht
• Affiliates & Partners

Popular Destinations & Events

• St Tropez Yacht Charter
• Monaco Yacht Charter
• St Barts Yacht Charter
• Greece Yacht Charter
• Mykonos Yacht Charter
• Caribbean Yacht Charter

Featured Charter Yachts

• Maltese Falcon Yacht Charter
• Wheels Yacht Charter
• Victorious Yacht Charter
• Andrea Yacht Charter
• Titania Yacht Charter
• Ahpo Yacht Charter

Receive our latest offers, trends and stories direct to your inbox.

Please enter a valid e-mail.

Thanks for subscribing.

Search for Yachts, Destinations, Events, News... everything related to Luxury Yachts for Charter.

Yachts in your shortlist

• GRAINGER DESIGNS

CRUISING NEWS

Never too young to enjoy a nice sunset.

 Looloo (left) and Lucky McGee enjoying the cruising lifestyle aboard Chincogan 52 Moonraker  anchored at the mouth of the estuary at the south end of Ko Phra Thong after spending a couple of weeks at Ko Phayam.

Then and now

The seafront of Cartagena in Colombia is the backdrop for two sailing vessels of different epochs and sharply contrasting character.

Against the sea wall  Galeon Bucanero , a replica of a Spanish galleon of the seventeenth century is totally at home against the fortifications of this historically significant Spanish port city.

In the foreground Chincogan 52  Sole currently circumnavigating the globe stops over en route to Panama and the Society Islands.

Over the years I've received many wonderful photos of our boats from around the world. This one is an absolute classic. Many thanks to Mike and Sarah Mason for the shot.

SAILING CATAMARANS

• Scroll to top

The evolution of yacht design

Evolution of yacht design, Superyacht builders, Marine boat construction, Hull marina architecture

The future of yacht design

9 September 2024

Author: Joanna Lewis

Yacht design is constantly evolving as yacht designers push the boundaries of traditional design and new technologies come to the fore.

The world’s most iconic yachts boast striking design features that set them apart from other vessels, from innovative naval architecture to design features that focus on enhancing a yacht’s green credentials.

Here we take a look at some of the most pioneering yacht design trends changing the yachting industry for the better.

Interior yacht design trends

Interior yacht design has changed significantly to factor in modern yachting lifestyles.

Yacht interiors now have a strong focus on flexible layouts that are more open-plan. Furthermore, there is a growing trend for onboard spaces that blur the boundaries between a yacht’s interior and exterior areas. Vast glass sliding doors that can be fully opened, retractable roofs, and fold-down balconies are designed to completely eliminate any boundary between a yacht’s interior and exterior.

Wellness is a big part of the yachting lifestyle, with private yachts now dedicating a significant portion of their real estate to spas, fitness suites, and yoga and meditation areas. Interior designers are also now bringing nature onboard, with hydroponic and vertical gardens that not only enhance wellbeing but also offer chefs access to an organic garden.

The latest interior yacht design trends are also harnessing exciting new materials such as sustainable textured wood, recycled glass, natural stone, and fine fabrics with a firm nod to organic forms that mimic nature.

Finally, advances in digital technology are transforming interiors, with vast tech windows or walls that offer virtual views and streaming services.

Exterior yacht design trends

Exterior yacht design has, arguably, seen the most significant shift in design trends from vessels with soft curved exteriors that mimic the organic shapes found in nature to avant-garde vessels that challenge conventional yacht design.

One key advancement in technology has been glass, which has led to a slew of eye-catching vessels with vast glass superstructures. Not only does the use of glass create head-turning vessels, but this material also floods the interior with light, while providing owners and their guests with breathtaking views of the ocean.

In addition, yacht exteriors are becoming more striking, with deck spaces being used in new ways. Yacht designers are now placing more emphasis on a yacht’s exterior with an increasing amount of real estate being designated to alfresco dining.

Vast beach clubs are now the norm on modern-day vessels, enhancing an owner’s connection to the water and direct access to the sea. It is common to see multiple exterior decks for relaxing and entertaining.

New advances in hull design are also helping to transform onboard comfort and the overall performance of luxury yachts. A hull typically amounts to around 70% of a yacht’s total structural design, making hull design a complex part of a yacht’s overall design.

Thanks to advances in hull designs, modern yachts now boast enhanced seakeeping and energy efficiencies.

There is no question that the world of yacht design is constantly evolving as designers seek to create ever more eye-catching vessels that meet the demands and lifestyle habits of today’s yachting enthusiasts

Comments on a guide to Evolution of yacht design – marine boat construction are welcome

Boat Design Articles

New Yachts 2018

Yachtsman’s House on the Isle of Wight

Marina Architecture

Building a Superyacht

Comments / photos for the Evolution of yacht design – modern boat construction page welcome.

Classic 420

Lightweight & capable

Lightweight & capable, the Classic 420 can be built to suit your tender requirements. Excellent layout options mean this model can be tailored to be the perfect beach hopper, tender or family day boat. An optional roll bar also provides the option of using this model for watersports & with a max crew of 8 no one needs to miss out on the fun!  

Key Features

4 Colour Schemes

Specifications

Overall Length

Internal Length

Overall Width

Internal Width

Tube Diameter

# of Air Chambers

Maximum Load

Maximum People

Boat only Weight

Engine Shaft

Design Category

Package size for boat (l x w x h)

390 x 110 x 85cm

12'8" x 3'6" x 2’8", standard features.

• ORCA® Hypalon or PVC tube
• Flush mount non-return valves
• High tensile chromated & powder coated aluminum hull
• Integrated transom supports
• Self-draining deck
• Lifting points and towing eyes
• Heavy duty rubbing strake
• Welded seams (PVC)
• Tow bridle points
• Brushed foam teak finish deck
• Full length keel guard
• Highfield dry bag
• Foot pump, oars, repair kit
• Electrical pack for boat & console
• Console & seat
• FRP Bow step & bow cushion

Optional Equipment

We sailed around the world and we couldn’t be happier of our decision with the dinghy! It has been by far the best companion for our circumnavigation. Amazing quality, durability and must of all safety and fun! Thank you Highfield

Sailing Vessel Maroro (@sv.maroro)

Adventure Locker

Vendee globe, are you ready to explore, our partners.

• Classic 260
• Classic 290
• Classic 310
• Classic 340
• Classic 360
• Classic 380
• Classic 400
• Classic 460

Shhh! Ohtani chase kept quiet by design

Blue jays stay tightlipped in pursuit, while dodgers manager admits to their meeting.

Keegan Matheson

NASHVILLE, Tenn. -- Silence is golden and secrecy is sublime. 

Standing in the eye of the biggest, boldest pursuit in franchise history, the Blue Jays aren’t saying a word. Even the name “ Shohei Ohtani ” is spoken carefully, each syllable tiptoeing gently to the next. 

Don’t rock the boat. Don’t wake the baby.

The secrecy with which baseball’s brightest star lives his life has taken over his free agency, which is bubbling to a boil here at the Winter Meetings. Earlier this offseason, ESPN’s Jeff Passan reported that it would be “held against” potential suitors if news leaked that he’d visited a specific team.

Well, it’s happening.

Every good drama has a shocking confession, and this one came from Dodgers manager Dave Roberts on Tuesday afternoon, admitting that he and members of Los Angeles’ front office had met with Ohtani in recent days. It all went very well, the veteran manager thought, and besides, the news would get out eventually.

“Clearly,” Roberts said, “ Shohei is our top priority .”

This was a wailing siren through the silence, because even following reports that Ohtani had toured Toronto’s training facilities in Dunedin, Fla., over the weekend, the Blue Jays refused to give that fire any oxygen, instead letting it live as a detail and nothing more.

Soon after Roberts dropped that nugget, though, Dodgers general manager Brandon Gomes stood before a throng of cameras -- less than 50 feet from Blue Jays GM Ross Atkins doing the same -- and struck a much different tone. Gomes acknowledged the comment made by his manager, said he was surprised that it was made and went no further. No comments on Ohtani, no comments on a meeting that may or may not have happened. 

That toothpaste isn’t going back in the tube.

Across the room, Atkins spoke vaguely, dancing in the shadows between questions. It’s the same approach he took Monday, when his in-person media availability was suddenly shifted to Zoom , where the GM was cryptic with details as he sat in front of a blank, white wall, refusing to answer where in the world he was. 

“Everything that we’re doing to make the team better, to the extent that we will keep private, we will do,” Atkins said. “Meetings that occur, don’t occur, I’m not going to get into the specifics of.”

It’s remarkable to watch this happen in real time, a big league GM sidestepping questions not as standard practice, but as an act of strategy that fans are suddenly praising. There’s an elephant in the room, but Atkins will not confirm whether elephants do or do not exist. 

“There’s an incredible amount of energy, an incredible amount of buzz around the game and around several potential opportunities, certainly one that is historic, potentially,” Atkins said.

Atkins is built for this game. He’s the Shohei Ohtani of secrecy.

Sign up to receive our daily Morning Lineup to stay in the know about the latest trending topics around Major League Baseball.

The Blue Jays’ GM went as far as saying that they are “fortunate to be one that’s being considered,” but offered no details about the reported visit to the club’s player development complex over the weekend.

Manager John Schneider did the same, saying “we meet with lots of players” and sticking to the script throughout his media availability. When a reporter joked that Schneider looked tanned when asking about his whereabouts and involvement in said meeting, Schneider just cracked another smile.

“I live in Florida,” he said.

The logic and logistics of it all point toward a decision coming soon from Ohtani. The Blue Jays and Dodgers are clearly among the front-runners here, and while it’s unclear what impact Roberts’ revelation and recent reports will have on Ohtani’s decision, these two clubs are clearly involved in the final sprint. Others, including the Giants, Cubs and Angels, have also widely been linked to this historic chase. 

When this news breaks, the landscape of Major League Baseball will tilt in an instant. Until then, it’s one of the biggest secrets in baseball history and the Blue Jays aren’t making a sound.